![background image](http://html.mh-extra.com/html/taymor/astral-06-4022/astral-06-4022_installation-instructions_823441001.webp)
INSTALLATION INSTRUCTIONS
ASTRAL 06-4022
ROMAN TUB FAUCET
TURN OFF
TURN OFF
SI
LI
CO
NE
Your installation may require
new supply lines.
(Supply lines are not included.)
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1
THANK YOU
FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers
Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench
Silicone caulk
2
TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves.
These are usually found near water meter.
WARNING: READ ALL
the instructions completely before beginning.
READ ALL
warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help?
Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
3
DECK PREPARATION
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to 1-11/16” thick.
4
INSTALL THE VALVE SYSTEM
From underneath the deck, insert valve body with rubber washer (1), metal washer (2) and
mounting nut (3) through holes on the right (cold) side. From above, thread flange (4) onto
valve stem. Tighten mounting nut (3), so that the flange (4) sits flush to the surface of working
area. Then insert the other valve body through holes on the left (hot) side and install in the
same way. NOTE: HOT side end valve is labeled.
Screw the handle seat (1) onto the flange (2). Place the handle (3) onto the
inverter (4) and secure with screw (5). Insert the index (6).
6
7
8
Place the spout assembly (1) through mounting hole in deck. Secure the spout assembly
(1) with rubber washer (2), metal washer (3) and nut (4).
Mount the spray support assembly. Place the spray support assembly (1) through
mounting hole in deck. Secure the spray support assembly (1) with washer (2) and nut
(3). Tighten nut securely with wrench.
Screw the connector (1) onto tube (2). Inset the hand held shower (3) into the spray
support assembly (4). Screw the shower hose coupling (5) onto the connector.
5" m
in.(12
7mm
)
4~6"(102-152m
m)
8~16
"(203
-406m
m)
3" m
in.
(76
mm
)
Ø1-1/8"
(29mm)
1-11
/16" (43mm) MAX. DEC
K THICKNESS
Ø1-3/8"
(35mm)
Ø1-9/16"
(40mm)
Ø1-3/8"
(35mm)
4
3
1
2
1
2
3
4
1
2
3
1
2
3
4
5
1
3
5
6
2
4
5