background image

TANKLESS 

WATER HEATER

CERTIFIED

R

DESIGN

CERTIFIED

®

AP16115-1 (8/12)

USE AND CARE MANUAL

With Installation Instructions 

for the Installer
Noncondensing 199,900 Btu/hr, 180,000 Btu/hr, 

and 150,000 Btu/hr Models

Printed in USA

Do not destroy manual. Please read 

carefully and keep in a safe place for 

future reference.

For Your Safety!

•  Do not store or use gasoline or 

other flammable vapors and liquids 

in the vicinity of this or any other 

appliance. To do so may result in 

an explosion or fire.

•  Installation and service must be 

performed by a qualified installer, 

service agency, or the gas 

supplier.

What to Do If  

You Smell Gas

•  Do not try to light any  

appliance.

•  Do not touch any electrical 

switch; do not use any  

phone in your building.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow 

the gas supplier’s instructions.

•  If you cannot reach your gas 

supplier, call the fire department.

•  Do not return to your home until 

authorized by the gas supplier or 

fire department.

If the information in these instruc-

tions is not followed exactly, a fire 

or explosion may result, causing 

death, personal injury, or property 

damage.

WARNING:

 

WARNING:

This water heater is not suitable 

for use in manufactured (mobile) 

homes.

Summary of Contents for 000 Btu/hr









































































Reviews: