background image

TR624

TM

2.4GHz 6-CHANNEL RECEIVER

This receiver is capable of full-range operation 

for small electric and sport scale aircraft types. 
Its SLT protocol makes it compatible with all 

Tactic brand 2.4GHz aircraft transmitters, and 

other brand radios that include the SLT protocol. 

Refer to the instructions with the aircraft to determine the optimum position for installing the receiver. In some aircraft it’s recommended 
to fi rst wrap the receiver in protective foam, and then use hook-and-loop material to mount it to the aircraft.

IMPORTANT! 

Pay close attention to how the receiver/antenna is oriented inside the model. It’s best to keep the antenna 

unobstructed from the outside of the model as much as possible.

Linking the TR624 receiver to the Tactic/SLT compatible transmitter ensures sole communication between the two, and prevents 
other transmitters from being able to control the receiver.

1.

 Turn on the Tx.

2.

 Apply power to the Rx.

3.

 If the Rx LED fl ashes once and then stays on, the Rx is 

already linked to the Tx and you can skip to the next section. 
Otherwise, insert a small diameter screwdriver through the hole 
marked “LINK” and press the pushbutton until the Rx LED glows 
red and then turns off after about one second.

4.

 Release the “LINK” button.

5.

 If the linking is successful, the Rx LED will fl ash once and 

then remain ON.

6.

 Test for proper Tx/Rx functionality before use. If the radio 

doesn’t appear to have become properly bound, repeat steps 
1–5 above.

If the receiver is powered without the transmitter being turned on, or signal from the transmitter is not recognized by the receiver, 
the receiver will go to failsafe mode as described in the following section.

The radio system’s failsafe function is controlled by the TR624 receiver, which engages in the event that the signal from the Tx 

somehow becomes interrupted. In such case, channels 1, 2, 4, 5, and 6 will hold their last recognized position.

Throttle, channel 3, however, can move to a position which is pre-set by the user during the linking process. The factory default 

failsafe position for channel 3 is to move to 0% throttle. The throttle’s failsafe position can be manually set to any other position if 
desired, as follows:

1.

 

IMPORTANT:

 Make sure the throttle channel’s servo reverse 

setting is in the correct position for the application.

2.

 Apply power to the Tx, then the Rx.

3a.

 If using an ESC: do NOT arm the ESC, or attempt to adjust 

the throttle’s failsafe position if the ESC is armed. 

NOTE:

 If you’re 

using an ESC which has a signal loss feature, its pre-set failsafe 
position will be irrelevant as the receiver’s failsafe function will 
cease the throttle operation if the signal is lost.

3b.

 If using a combustion engine: do NOT attempt to adjust the 

throttle’s failsafe position while the engine is operating.

4.

 Move the Tx throttle stick to the desired throttle failsafe position.

5.

 Press and hold the receiver’s “LINK” button. The Rx’s LED 

should blink twice. Release the LINK button, and the LED should 
stay on continuously. The Tx and Rx should now be linked, with 
the throttle failsafe in the new position as set above.

6.

 Prior to fl ight, check the position of the failsafe. It’s best to 

check the system with the propeller removed from the aircraft 
and the aircraft restrained.

Check the instruction manual included with the Tactic radio for the proper steps to perform a system check before fl ight.

WARNING

! Always make sure that power is applied to the transmitter BEFORE applying power to the receiver and servos, 

and the Tx throttle stick is at minimum (idle) position. Failure to do so could result in the model becoming uncontrollable 
and cause a safety hazard. It’s best to check the system with the propeller removed from the aircraft.  Always perform 

OVERVIEW AND INSTALLATION

LINK THE RECEIVER TO THE TACTIC/SLT COMPATIBLE TRANSMITTER

FAILSAFE FUNCTION

SYSTEM AND RANGE CHECK

Reviews: