Suntor ST10NPT User Manual Download

Page: 1 / 12

1st

ST5/10/20NPT User Manual

Contents

...............................................................................................................................................................................

II. Interface

................................................................................................................................................................................

1. Indicator

........................................................................................................................................................................

III. Precautions for integration

...................................................................................................................................................

IV. Precautions When Powering On

...........................................................................................................................................4th

V. List of in-box items

.................................................................................................................................................................5th

VI. Setup

.....................................................................................................................................................................................5th

1. Set the IP Address

..........................................................................................................................................................5th

2. Set Serial Port Configuration

......................................................................................................................................... 6th

VII. Antenna Installation

............................................................................................................................................................ 7th

1. Multi-rotor UAV

............................................................................................................................................................. 7th

2. Fixed Wing UAV

..............................................................................................................................................................7th

VIII. Software Operation

............................................................................................................................................................ 8th

1. Start Connecting Tdd-cofdm equipment....................................................................................................................... 8th
2. Restart TDD-COFDM Control Panel software.............................................................................................................8th

3. RF Configuration method

..........................................................................................................................................8th

4. Seria Configuration method:....................................................................................................................................... 10th

5. RS232 Configuration Menu.........................................................................................................................................11th
6. IP New Network Configuration method:.................................................................................................................... 12th
7. RF New NET Configuration method.......................................................................................................................... 12th

7.1. RF Net ID:........................................................................................................................................................ 12th
7.2. RF Encrypt KEY ............................................................................................................................................. 12th

SUNTOR ELECTRONICS CO., LIMITED

V1.0

Summary of Contents for ST10NPT













Search results

Summary of Contents for ST10NPT

Reviews:

Related manuals for ST10NPT

Brands by name

Popular brands

Suntor ST10NPT, User Manual

Search results

Summary of Contents for ST10NPT

Reviews:

Related manuals for ST10NPT

Brands by name

Popular brands