background image

Please Do Not Return This Product To The Store!

Contact Escalade

®

Sports customer service department at:

Phone:

1-800-467-1245

Toll

Free !

Fax:

1-866-873-3533

Toll

Free !

E-mail:

[email protected]

Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at:

www.escaladesports.com

ON-LINE TROUBLE SHOOTING

TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS

FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE

®

SPORTS PRODUCT INFORMATION

2L-5027-02

Ó

Ó

Ò

Ò

TABLE TENNIS TABLE

MODEL NO.

T8730 (ST3000)

1. Read this manual carefully before starting assembly.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons

before assembling or ordering parts.

3. Do not tighten hardware until instructed to do so.

4. Tools required for assembly:

Read each step completely before beginning

each step.

If hardware is tightened too soon, mounting

holes may not align and parts may not easily fit together. Leave locknuts slightly loose until you are
instructed to tighten them.

Phillips Screwdriver, Two 9/16” Wrenches, Two 7/16” Wrenches.

Note: Adjustable wrenches can be substituted for wrenches.

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2008 Escalade Sports

O W N E R ' S M A N U A L

Summary of Contents for ST30000

















Reviews: