![background image](http://html.mh-extra.com/html/sti/ez-path-series/ez-path-series_installation-sheet_1376284001.webp)
INSTALLING OR PULLING CABLES
A resilient liner provides an adjustable seal within the pathway device. Liner must be protected from damage while adding or removing cables.
Wrap cable ends with a suitable low friction tape before inserting into the pathway. Where cable lubricants are used, low solids, water-based
products are recommended. This device is designed to be fully functional at all cable loadings from completely empty to visually filled, and
cables should easily slide through the pathway using minimal effort. IF RESISTANCE IS ENCOUNTERED, DO NOT FORCE CABLES OR
CABLE BUNDLES THROUGH THE PATHWAY. DAMAGE MAY RESULT. Upper curved liner may be depressed when inserting cables, if
necessary, using a flat, smooth implement and then removing it after cables are installed. The rectangular shape of the loading area coupled
with gentle pressure exerted by resilient liners will naturally distribute the cables at a relatively uniform height across the width of the device.
The use of a cable dressing/combing instrument to straighten and organize cables may help to maximize
usable space within the pathway device.
GROUNDING
At the option of the installer, this device may be grounded. After device(s) has been installed, insert
ground screws where indicated (See Fig. 3).
LABELING
Labels are provided with the device as well as wall plate kits. Larger orange colored label is intended
to be used to identify the device’s installer as well as to provide applicable UL System information.
Smaller secondary labels are included with double, triple, four and
seven gang mounting plates as an
optional method for identifying or marking cable types, uses, or
trades. Two sets of labels are provided
for marking both sides of wall or floor.
MAINTENANCE
No maintenance of the device is normally required. Interior
of device should be inspected before and after any modifications to cable bundle. If any damage to intumescent pads’ lining top and
bottom of the device is found, contact the factory to determine if replacement is required.
Page 1 of 2
Installation Sheet •
EZ-Path® SERIES 33 Multi-Purpose Split Mounting Plate
ZIS1004 - 3345
Fig. 1
TABLE B: Required Fasteners (Not Included)
Hourly Rating
Masonry
Gypsum Wallboard
1 Hour
1/8” (3 mm) by 1-1/2” (38 mm)
steel anchor with 3/8” (10 mm)
diam. steel washer
1/8” (3mm) by 1-1/4” (32 mm)
molly bolt with 3/8” (10 mm)
steel washer)
2 Hour
1/8” (3 mm) by 1-1/2” (38 mm)
steel anchor with 3/8” (10 mm)
diam. steel washer
1/8” (3mm) by 2” (51 mm)
molly bolt with 3/8” (10 mm)
steel washer)
Fig. 3
Fig. 2
INSTALLATION SHEET
EZ-Path
®
Series 33 Single Split Wall Plate
for Retro-Fit Applications
ZIS1004 - 3345
(Part No. EZP133R & EZDP33WR )
This product is designed to facilitate installation of the EZ-PATH
®
Fire
Rated Pathway in retrofit applications (around previously installed cables,
see Fig. 1) or in new or existing cabling applications where a large open-
ing (Fig. 2) or opposing offset openings have been created in either
gypsum board or masonry block wall assemblies. The two-piece plates
{assembled size 8” x 10” (200 x 250 mm)} and split insulative gaskets
are designed to make possible installation around existing cable bundles.
Before installing, using split gasket as a template, confirm that the assem-
bled plates will overlap the wall openings on both sides by a minimum
of 1” (25 mm) in all directions. Verify that fasteners will attach solidly to
undamaged, structurally intact wall surfaces. Note that the pathway open-
ing in the plate assembly is offset. This feature allows plate assemblies on
opposing sides of the wall to be rotated independently of each other in 90˚
increments to best adjust to irregular or offset openings.
NOTE: Pathway is designed to be installed through walls with the lid
(labeled surface) facing upwards.
GENERAL - READ COMPLETELY BEFORE INSTALLING
TABLE A: Parts List
Qty. Description
Qty. Description
2 Large plate section
1
5/64 Allen key
2 Small plate section
10 8-32 x 1/4” lg. set screws
2 8” x 10” Split insulative gasket
(203 mm x 254 mm)
4
8-32 x 1/4” lg. Phillips screws
2 Ground screws
1
EZD33FWS*
*EZDP33WR only.