background image

GENERAL PRECAUTIONS

Use only Stanley STZ or Brother TZ tapes with this machine. Do not use any other
tapes.

Tapes are available in three different widths: 1/4” (6 mm), 3/8” (9 mm) and 1/2” (12
mm).

Do not pull the tape since this may damage the tape cassette.

Do not attempt to cut the tape while printing or feeding since this will damage the
tape.

Do not clean the machine with alcohol or other organic solvents. Use only a soft, dry
cloth.

Remove the batteries and disconnect the AC adapter if you do not intend to use the
machine for an extended period of time.
Note: If power is disconnected for more than three minutes, all text shown in the

display and any text files stored in the memory will be lost.

Do not put any foreign objects into or anything on the machine.

Do not expose the machine to high temperatures or high humidity. Never leave it on
the dashboard or in the back of your car.

Do not use the machine in dusty places, and keep it out of both direct sunlight and
rain.

Do not leave any rubber or vinyl on the machine for an extended period of time.
Doing so may cause staining.

After inserting a new tape cassette, advance the tape by holding down 

 and

pressing 

 once.

Do not touch the print head mechanism. If the head is touched, clean it immediately
with a soft wipe (e.g., a cotton swab) to avoid permanent damage.

To avoid injuries, do not touch the cutter’s edge.

Use only the AC adapter designed exclusively for this machine. Use of any
other adapter will void the warranty.
Please contact a Brother dealer for details.

POWER SUPPLY

Batteries

Since this machine is compact and portable, it can be used anywhere by installing six
AAA alkaline batteries (LR03). When changing the batteries, always replace all six at the
same time.

1

Press in on the rough area at the top end of the machine and
fold open the back cover.

2

If batteries are already installed, remove the tape cassette (if one is
installed) by pulling it straight out, and then remove the batteries.

3

Insert the batteries into the battery compartment with the
positive end of the bottom three batteries pointing toward the top
end of the machine, and the positive end of the top three
batteries pointing in the opposite direction.
Note: When replacing the batteries, insert the new ones within

three minutes of removing the old ones, otherwise all text
shown in the display and any text files stored in the
memory will be lost (unless the machine is plugged into
an outlet with the AC adapter).

4

Securely close the back cover, making sure that it snaps into place.

Optional AC adapter

The AC adapter allows you to use this machine wherever an electrical outlet is available.
Use Brother’s AD-30 adapter for your new ST-1150/1150DX.

1

Insert the plug on the adapter cord into the adapter jack on the bottom end of the
machine.

2

Insert the plug into the nearest standard electrical outlet.

OVERVIEW

  

Display

Backspace key

SPACE KEY

As on a word processor, press 

 to add a blank space to your text.

RETURN KEY

Press 

 when you wish to accept or confirm a setting, or end the first line of text and

start the second.

To add a second line, press 

 once. The return mark (

 ) appears in the text to

indicate the end of the first line and the beginning of the second.

Note: Two lines of text can only be entered if 3/8” (9-mm)- or 1/2” (12-mm)-wide tape

is installed.

To  accept or confirm a setting from a list, press 

 once.

ACCENTED CHARACTERS

You can also choose from a list of other accented characters that can be added to your
text.

1

Press 

 if you want the accented character to be an upper case letter.

Note: To quit the following procedure at any time without making any changes, press 

.

2

Hold down 

 and press 

. The message “A-U?” appears in the display.

3

Press the key for the letter in the accented character that you wish to add, and then

press 

 and 

 until the cursor is positioned under the desired accented

character.

4

Press 

 to add the selected character to your text.

SYMBOLS

In addition to the letters, symbols, and numerals on and above the keys, there are 72
symbols available with the Symbol function. These symbols are divided into 9 groups,
corresponding to the letters A through I.

1

Press 

. The message “A-I?” appears in the display.

2

Press the key for the letter of the group containing the symbol that you wish to add,

and then press 

 and 

 until the cursor is positioned under the desired symbol.

3

Press 

 to add the symbol to the text.

SIZE

The characters in the text can be set to one of five different sizes in addition to AUTO,
which automatically adjusts the characters to the largest possible size according to the
width of the installed tape. The currently selected size setting is shown by the indicators at
the top of the display. All of the size indicators light up when the AUTO setting is selected.

SIZE 1 (A: standard size)

SIZE 2 (A: double width)

SIZE 3 (

A

: double height)

SIZE 4 (

A

: double width & double height)

SIZE 5 (

A

: 4

×

 width & double height)

              

Note:

• If there are two lines of text, they are printed with the SIZE1 setting applied,

regardless of the selected size setting.

• To quit the following procedure at any time without making any changes, press 

.

1

Press 

.

2

Press 

 and 

 until SIZE is displayed, and then press 

 (or 

). The

current size setting appears in the display.

3

Press 

 and 

 until the desired size setting is displayed.

4

Press 

 (or 

) to apply the selected size setting to the text.

With your new ST-1

150/1150DX, you can create labels for any application. Select from the many frames,

character sizes and styles to design beautiful custom labels. In addition, the variety of tape cartridges

available allows you to print labels with different widths and exciting colors.

Y ou no longer have to worry about urgent tasks that require professional printing. 

The quality and

performance of the ST-1

150/1150DX make it an extremely practical machine.

Although this machine is easy to use, we suggest that you read this manual carefully before starting and

keep the manual in a handy place for future reference.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-

Reorient or relocate the r

eceiving antenna.

-

Increase the separation between the equipment and r

eceiver.

-

Connect the equipment to an outlet on a circuit dif

ferent from that to which the

receiver is connected.

-

Consult the dealer or an experienced radio/TV technician for help.

-

Changes or modifications not expressly appr

oved by Brother Industries, Ltd.

could void the user’s authority to operate the equipment.

Return key

Group

Symbols

A

Ü

ü

Ç

ç

Æ

æ

á

é

B

í

ó

ú

Ã

ã

C

Õ

õ

Ñ

ñ

¡

¿

§

#

D

·

°

;

%

+

×

÷

=

E

$

¢

[

]

2

3

2

3

F

4

TM

®

©

G

H

I

_

~

INTRODUCTION

MODEL ST-1150/

1150DX

USER’S GUIDE

LA3255001

Printed in China

Function key

TAPE CASSETTES

A tape cassette is supplied with this unit. Stanley STZ or Brother TZ tapes used with this
machine are available in a variety of colors and three tape widths (1/4” (6 mm), 3/8” (9
mm) and 1/2” (12 mm)).

1

Press in on the rough area at the top end of the machine and
fold open the back cover.

2

If a tape cassette is already installed, remove it by pulling it
straight up.

3

If the ink ribbon in the other tape cassette is loose, use your
finger to wind the toothed wheel in the direction of the arrow on
the cassette until there is no slack in the ribbon. Also, make sure
that the end of the tape feeds under the tape guides.
Note: If you are using a new tape cassette provided with a

stopper, be sure to remove the stopper.

4

Insert the tape cassette firmly into the compartment, making
sure that the entire back of the cassette contacts the bottom of
the compartment.
Note: When inserting a tape cassette, make sure that the inner

ribbon does not catch on the corner of the metal guide.

5

Securely close the back cover, making sure that it snaps into place.

6

Feed the tape by holding down 

 and pressing 

 once,

and then push in the tape cutter lever to cut the tape.

STARTING

Press 

. If batteries have been installed or the machine has been plugged in using the

optional AC adapter, the previous session’s information is displayed when the machine is
turned on. This feature allows you to stop work on a label and turn off the machine, then
return to it later without having to re-enter the text.
The machine automatically turns off if no key is pressed within five minutes. The current
session’s information is stored in the machine’s internal memory and displayed when the
machine is later turned on again.

CODE KEY

By holding down 

 and pressing a key with a function, character or accent written

above it, you can use the corresponding function or add the corresponding character to
your text.

CAPS KEY

By pressing 

 to enter Caps mode, you can add upper-case letters to your text by

simply pressing the character keys. When this mode is on, the Caps indicator in the top-
left corner of the display comes on. To exit Caps mode, press 

 until the Caps

indicator goes off.

NUM KEY

By pressing 

 to enter Num mode, you can add numbers to your text by simply

pressing the corresponding keys. When this mode is on, the Num indicator in the bottom-
left corner of the display comes on. To exit Num mode, press 

 until the Num

indicator goes off.

DISPLAY

This machine’s LCD shows one row of 8 characters; however, the text that you enter can
be up to 55 characters in length. The 8-character display is like a window which moves
across the text.

1234567890123456789012345678901234567890123456789012345

CURSOR MOVEMENT

You can view and edit different parts of the text by moving the cursor backward and
forward.

To move the cursor one character at a time, press 

 or 

.

To move the cursor to the beginning of the text, hold down 

 and press 

.

To move the cursor to the end of the text, hold down 

 and press 

.

BACKSPACE KEY

This key can be used to remove characters from your text, clear all of the text or cancel
the current function and return to the text input mode.

To delete the character to the left of the cursor or to cancel a function, press 

.

To clear all of the text that is currently entered, hold down 

 and press 

.

Tape cutter lever

Letter

Accented character

Letter

Accented character

A

À

Á

Ä

Â

Ã

Æ

a

à

á

ä

â

ã

æ

C

Ç

c

ç

E

È

É

Ë

Ê

e

è

é

ë

ê

I

Í

Ï

Î

i

í

ï

î

N

Ñ

n

ñ

O

Ó

Ö

Ô

Õ

o

ó

ö

ô

õ

U

Ù

Ú

Ü

Û

u

ù

ú

ü

û

Back cover

Batteries

Print head

On/Off key

Tape cassette

Tape exit slot

Patent numbers and patent publication numbers which are r

elated to this product

are as below:

USP4839472

USP4983058

USP5120147

USP4927278

USP5009530

USP4976558

USP5069557

Num key

Caps key

Reviews: