background image

SERVICE MANUAL

9-870-060-13

Sony Corporation

2004I05-1

e Vehicle Company

© 2004.09

Published by Sony Engineering Corporation

FM/AM CASSETTE CAR STEREO

US Model

Canadian Model

UK Model

E Model

SPECIFICATIONS

XR-1100

Model Name Using Similar Mechanism  NEW

Tape Transport Mechanism Type            MG-36SZ10-32

Cassette player section

Tape track

4-track 2-channel stereo

Wow and flutter

0.13 % (WRMS)

Frequency response

30 – 15,000 Hz

Signal-to- noise ratio

55 dB

Tuner section

FM

Tuning range 
US and Canadian models : 87.5 – 107.9 MHz

Antenna terminal

External antenna connector

E and UK models:

E and UK models:

FM tuning interval :
50kHz/ 200kHz
switchable
87.5 -108.0MHz
(at 50 kHz step)
87.5 -107.9 MHz
(at 200 kHz step)

Intermediate frequency

10.7 MHz

Usable sensitivity

9 dBf

Selectivity

75 dB at 400 kHz

Signal-to-noise ratio

65 dB (stereo),
68 dB (mono)

Harmonic distortion at 1 kHz

0.7% (stereo),
0.4% (mono)

Separation

35 dB at 1 kHz

Frequency response

30 – 15,000 Hz

AM

Tuning range

530 – 1,710 kHz

Antenna terminal

External antenna connector

Intermediate frequency

10.71 MHz/450 kHz

Sensitivity

30 

µ

V

Power amplifier section

Outputs

 Speaker outputs

(sure seal connectors)

Speaker impedance

4 – 8 ohms

Maximum power output   45 W 

× 

4 (at 4 ohms)

AUDIO POWER SPECIFICATIONS (US model only)

POWER OUTPUT AND TOTAL HARMONIC DISTORTION
17 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than

1% total harmonic distortion.

US and Canadian models :

AM tuning interval:
9 kHz/10 kHz switchable
531 – 1,602 kHz
(at 9 kHz step)
530 – 1,710 kHz
(at 10 kHz step)

– Continued on next page –

Ver 1.2  2004.09

Summary of Contents for XR-1100













































Reviews: