background image

– 1 –

Model Name Using Similar Mechanism NEW

CD

CD Mechanism Type

KSM-213CCM

Section

Optical Pick-up Name

KSS-213C

TC

Model Name Using Similar Mechanism CFD-ZW150/ZW160

Section Tape Transport Mechanism Type

MF-ZW150

SERVICE MANUAL

US Model

Canadian Model

CFD-C1000

CD RADIO CASSETTE-CORDER

MICROFILM

SPECIFICATIONS

– Continued on next page –

AUDIO POWER SPECIFICATIONS (US Model)

POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 6-ohm loads, both channel driven
from 75 - 15,000 Hz; rated 10 W per
channel-minimum RMS power, with no more
than 1% total harmonic distortion in AC
operation.

Other Specifications

CD player section

System

Compact disc digital audio system

Laser diode properties

Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min (rpm) (CLV)

Number of channels

2

Frequency response

20 - 20,000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

Radio section

Frequency range

FM: 87.6 - 108 MHz
AM: 530 - 1,710 kHz

Antenna

FM: Telescopic antenna
AM: Loop antenna

Cassette-corder section

Recording system

4-track 2 channel stereo

Fast winding time

Approx. 120 s (sec.) with Sony cassette C-60

Frequency response

TYPE I (normal): 100 - 10,000 Hz

Ver 1.2  2000. 10

Summary of Contents for CFD-C1000 - Boombox With Cd





















Reviews: