background image

 

 

 

 

 

Solar PV module installation manual

 

 

 

 

 

Version  Number

2020-A1 

 

Issued  Date

2020-4-23 

 

Amended  Date

-- 

 

Corporation:Nanjing Solglass  Science&Technology Co.,  Ltd. 

 

 

 

 

The  manual  applies  to the  following  product  models: 

 

Solartrix 1200-400-xx

 

 

 

 

Note

“xx” 

represents  the  specific  power  of  the  module,  in steps of 5W. 

 

 

 

 

 

 

 

 

 

 

 

Important safety Tips

 

 

 

 

This installation manual provides Nanjing Solglass Science&Technology Co. , Ltd. 

(Hereinafter referred to as "SOLGLASS”) photovoltaic modules (hereinafter referred to as 
"modules") of the installation and safe use of information. All safety aspects of this 
guide,precautions and local regulations should be followed during modules installation and 
routine maintenance.Precautions and local regulations. 

 

Installing  module  system  requires  expertise  and  knowledge,  it  can  only  be  done  by 

qualified personnel. Please read this installation manual carefully before installing and using 
modules.  The  installer  shall  be  familiar  with  the  mechanical  and  electrical  requirements  of 
the system. Please keep this manual for future maintenance and repair or when the modules 
need to be sold or processed. 

 

Please contact the SOLGLASS after service department for more explanation. 

 

 

 

 

 

 

Summary of Contents for Solartrix 1200-400 Series















Reviews: