background image

Swing Gate Opener Manual

Warnings

Please read this instruction manual carefully before the installation of gate-automated
system.

This manual is exclusively for qualified installation personnel. We are not responsible for
improper installatio and failure to comply with local electrical and building regulations.

* Be aware of the hazards that may exist in the procedures of isntallation and operation of
the gate-automated system. Besides, the installation must be carried out in conformity with
local standards and regulations.

* If the system is correctly isntalled and used following all the standards and regulations, it
will ensure a high degree of safety.

* Make sure that the gates work properly before installing the gate-automated system and
confirm the gates are appropriate for the application.

* Do not let children operate or play with the gate-automated system.

* Do not cross the path of the gate-automated system when operating

* Please keep all the control devices and any other pulse generator away from children to
avoid the gate-automated system being activated accidentally.

* Do not make any modifications to any components except that it is mentioned in this
manual.

* Do not try to manually open or close the gate before you release the gear motor.

* If there is a failure that cannot be solved and is not mentioned in this manual, please
contact qualified installation personnel.

* Do not use the gate-automated system before all the procedures and instructions have been
carried out and thoroughly read.

* Test the gate-automated system weekly and have qualified installation personnel to check
and maintain the system at least every 6 month.
* Install waring signs ( if necessory) on the both sides of the gate to warn the people in the
area of potential hazards.

Summary of Contents for SP-SWG-ARM-350










Reviews: