SHO-ME@
MODEL NO. 21.7462
WIRING INSTRUCTIONS
';.
~
IMPORTANT! This product is NOT waterproof. It must be mounted in a clean, dry location.
~
TECHNICAL
SPECIFICATIONS
INSTALLATION
INPUT VOLTAGE
10 to 30 Vdc
INPUT CURRENT
5.5A at l2.8V, 2.6A at 25.6V
INPUT POWER
:
70.4 Watts'
OUTPUT POWER
60 Watts in high power mode.
40 Watts in low power mode.
OUTPUT ENERGY
51.5 Joules
FLASH PATTERNS
15
QUICK REFERENCE
I
I
I
I
I
I
I
I
I
I
.. .. .. ..
~~~~N
$J
'
;
8
!
..
;]
8
,
BLACK.. ..
WHIT..
fit
I
1
2
3
4
I
Strobe Head Outlets
,..,'a:: ..J'a::
'a::
::>0
~o
::>0
I
~~ a:~ ~~
015
[1J~
15
I
~
0
~
()
.. ..
YELLOW
j
'
!
RED
GREEN'
"
','
BLACK
BLUE
' '.'.'.
VIOLET
t
'tPower Connector
Control Connector
POWER HARNESS
~
-RED
_BLACK
-
VIOLET
CONTROL HARNESS
YELLOW
,_GREEN
,-
BLUE
~
STROBE
HEAD
EXTENSION
CABLES
(NOT INCLUDED)
H,a,y
"ty
exloo,loo
oabl"
hm
a GREEN wi""
Ughl
',ty 'xle""on
~bl"
ha" a REDwi""
RED or GREEN.
-
BLACK
~
WHITE
1.
Mounting:
Mount the power supply to a flat metal surface.
Mount in a clean, dry area. NEVERMOUNT
INENGINECOMPARTMENT!
Use the power supply as a template to mark the hole locations.
The mounting holes will accept up to a 1/4" bolt.
Note: Thepower supply baseplate must be connected to chassis
ground (GND) to reduce radio interference.
2.
Strobe Head Installation:
Plug the strobe head extension cables into the outlets.
.
Heads connected to outlets I and 3 flash at the same time.
.
Heads connected to outlets 2 and 4 flash at the same time.
.
Heads connected to I and 3 alternate with heads 2 and 4.
.
Be sure to use strobe heads with the correct power rating.
The total output power (60 Watts) of the MODEL 21.7462 is
distributed
to the strobe
heads
as follows:
I Head installed and activated
= 30 Watts.
2 Heads installed and/or activated = 30 Watts per head.
3 Heads installed and/or activated = 2 heads at 15 Watts each, 1...&.J.QJYa1ts.
4 Heads installed and/or activated = 15 Watts per head.
3.
Electrical Hookup:
If you have purchased a switch panel, follow the included
instructions. If you are wiring the system yourselffollow the
instructions below and the diagrams on the next page.
i:o
T""'
POWER
HARNESS:
.
Connect the RED wire to B through
a 15A fuse
(customer supplied) located at the battery.
.
Connect the BLACK wire to battery negative (-) or directly to
vehicle chassis.
Note: Use the correct
size
wirefor power connections. The length
of the wires determines the size needed.
1 to
lOft.
use 18AWGwire.
10 to 20ft. use 16A WG wire.
20 to 35ft. use 14AWG wire.
35 to 50ft. use 12AWGwire.
.
The VIOLET
wire activates LOW power mode. The output
power is reduced to 40 Watts in LOW power mode. Connect
VIOLET
to + 12/24V to activate LOW power mode, leave
disconnected
or connect to GROUND for high power mode.
N
~
I
(9
w
I
CONTROL
HARNESS:
UJLL<C»W: Flash pattern selection. Momentarily
connect to
+ 12/24V to advance to the next flash pattern in the PATTERN
LIST. Momentarily
connect for 3 seconds to reset to pattern #1.
The flash pattern will be retained when the MODEL
21.7462
is
turned off or if power is removed. To change flash patterns
frequently, connect UJLJL<C»Wto a momentary pushbutton located
in the passenger compartment.
GREEN: Activates Heads 1 and 2 when connected to + 12/24V
BLUE: Activates Heads 3 and 4 when connected to + 12/24V
NOTE:
VIOLET, YELLOW, GREEN, and BLUE are all Low Current
circuits and
can be wired with a minimum of 18AWGwire.
