Instructions for:
Glow Plug Removal Set
MODEL No:
SX0408.V2
1. SAFETY inSTRucTionS
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE inSTRucTionS cAREFuLLY. noTE THE SAFE oPERATionAL REQuiREMEnTS,
WARninGS AnD cAuTionS. uSE THE PRoDucT coRREcTLY AnD WiTH cARE FoR THE PuRPoSE FoR WHicH iT iS
inTEnDED. FAiLuRE To Do So MAY cAuSE DAMAGE AnD/oR PERSonAL inJuRY AnD WiLL inVALiDATE THE WARRAnTY.
PLEASE KEEP inSTRucTionS SAFE FoR FuTuRE uSE.
2. inTRoDucTion
3. SPEciFicATion
WARninG!
Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
Do noT
use tools if damaged.
Maintain tools in good and clean condition for best and safest performance.
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
Wear suitable clothing to avoid snagging.
Do noT
wear jewellery and tie back long hair.
Do noT
attempt to start engine or move vehicle whilst tools are fitted and work is in progress.
Ensure any disconnected fuel pipes are plugged to avoid spillage.
Account for all tools and parts being used,
Do noT
leave them in or near the engine. Return all parts to the case and store this in a
safe, dry, childproof location.
IMPORTANT:
These instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions,
or a proprietary manual, to establish the current procedure and data.
WARninG!
The warnings referred to in this guide cannot cover all possible conditions and situations that may occur. It must be understood
that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
SX0408.V2 Issue No: 1 - 10/09/13
Original Language Version
© Jack Sealey Ltd
●
Designed to remove damaged/broken glow plugs from cylinder heads.
●
Suitable for glow plugs with M8 x 1mm or M10 x 1mm thread.
●
Set includes all required adaptors for centring,drilling and pulling for the safe removal of the glow plug.
●
Supplied in storage case.
Model Number:.............................................................. ..SX0408.V2
Tap Dimensions:......................... ¼”-28UNF, M8 x 1mm, M10 x 1mm
Glow Plug Applications:................................ M8 x 1mm, M10 x 1mm
Key to Fig 1:
number
Part no.
Description
1................ SX0408.V2-01............................................ Puller Housing
2................
SX0408.V2-02................................... Drill Holding Adaptor
3................ SX0408.V2-03............ Puller Adaptor Mandrels (2 pcs/set)
4................ SX0408.V2-04........Pilot Drill Centring Sleeves (2pcs/set)
5................ SX0408.V2-05........................................... Hex Key (3mm)
6................ SX0408.V2-06........................................ Star Socket (E10)
7................ SX0408.V2-07................................ Drill Bit (7mm /5.5mm)
8................ SX0408.V2-08................................ Drill
Bit (9mm/5.5mm)
9................ SX0408.V2-09............................................. Ratchet T- Bar
10............... SX0408.V2-10................................... Pilot Drills (2pcs/set)
11................ SX0408.V2-11........................................... Tap (M10 x 1.0)
12............... SX0408.V2-12............................................. Tap (M8 x 1.0)
13............... SX0408.V2-13.......................................... Tap (¼”-28UNF)
Fig.1:
