InstructIon manual for:
COMPRESSOR 6LtR
diRECt dRivE 1.5hP
model no
:
SA0615
thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE REAd thESE iNStRUCtiONS CAREFULLY. NOtE thE SAFE OPERAtiONAL REQUiREMENtS, WARNiNGS & CAUtiONS.
USE thE PROdUCt CORRECtLY ANd With CARE FOR thE PURPOSE FOR WhiCh it iS iNtENdEd. FAiLURE tO dO SO MAY CAUSE
dAMAGE ANd/OR PERSONAL iNJURY ANd WiLL iNvALidAtE thE WARRANtY. PLEASE KEEP iNStRUCtiONS SAFE FOR FUtURE USE.
1.1.
ELECtRiCAL SAFEtY
WARNiNG!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
a residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
device (rcd) is used. It is particularly important to use an rcd with portable products that are plugged into a supply which is not protected
by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. the
Electricity at Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable appliance tester (Pat), at least once a year.
1.1.2. the
health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
if in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable appliance tester.
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6.
important:
ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7.
dO NOt
pull or carry the appliance by the power cable.
1.1.8.
dO NOt
pull the plug from the socket by the cable.
1.1.9.
dO NOt
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an asta/Bs approved uK
3 pin plug is damaged, cut the cable just above the plug and
dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
to rewire, connect the wires as indicated above -
dO NOt
connect either wire to the earth terminal.
1.1.10. Products which require more than 13amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a 30 amp supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. a reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the section of the cores in the cable is important and should be at least 1.5mm², but to be
absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we
recommend the use of 2.5mm² section cable.
1.2.
GENERAL SAFEtY iNStRUCtiONS
3
Familiarise
yourself with the application and limitations of the compressor.
3
ensure that the compressor is in good order and condition before use. If in any doubt do not use. contact an electrician or
your service agent.
WARNiNG! the compressor must be serviced by an authorised agent only. DO NOT tamper with, or attempt to adjust, the
pressure switch or the safety valve.
3
Before moving or maintaining the compressor,
ensure that it is unplugged from the mains supply and that the air tank pressure has been
vented.
3
only use recommended parts and accessories. using unauthorised items may be dangerous and will invalidate your warranty.
3
read the instructions regarding any air tool/accessory used with the compressor. ensure that the safe working pressure of any air
tool/accessory used exceeds the output pressure of the compressor.
3
Keep tools and other items away from the compressor when it is in use and keep the area clean and free of unrelated items.
3
ensure that the air hose is not tangled, twisted or pinched.
3
Keep children and unauthorised persons away from the work area.
7
dO NOt
dis-assemble compressor for any reason. the unit must be checked by qualified personnel only.
7
dO NOt
use the compressor outdoors, or in damp or wet locations and
dO NOt
operate it within the vicinity of flammable liquids, gases or solids.
7
dO NOt
touch compressor cylinder, cylinder head or pipe from head to tank, as these may be hot and will remain so for some time after shutdown.
7
dO NOt
attempt to move the compressor by pulling the air supply hose.
7
dO NOt
attempt to lift or move the compressor by any means other than by the handle.
3
remove ill fitting clothing, ties, watches, rings and other loose jewellery and contain long hair.
3
Wear approved safety eye protection (standard spectacles are not adequate).
3
use the compressor in a well ventilated area, keeping the air vents clear of obstructions.
7
dO NOt
restrict air flow around the compressor whilst operating it.
3
ensure that it is placed on a firm, level surface.
7
dO NOt
operate the compressor if you are tired or under the influence of alcohol, drugs or intoxicating medication.
1. SAFEtY iNStRUCtiONS
Original Language Version
sa0615 Issue: 2 - 20/02/12
fuse ratInG: 13amP
