Trolley jack 1.5Tonne aluminium/
sTeel rockeT lifT
Model no:
rjas1500.V2
Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safeTy
9
ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement
of damaged parts. Use genuine parts only. The use of improper parts may be dangerous and will invalidate the
warranty.
9
locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated
materials.
9
Use jack on level/solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
Place chocks under wheels of vehicle, but ensure the jack wheels are free to move and that there are no
obstructions.
9
ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if
automatic).
9
ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for
vehicle tilting.
9
ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst
the jack is in use. Place jack under lifting points recommended by vehicle manufacturer (see vehicle hand
book). ensure lifting point is stable and centred on saddle.
▲
DanGer:
Use the jack for lifting only, noT for supporting the lifted load.
9
Use suitable capacity axle stands under the vehicle before proceeding with any task.
9
ensure there are no persons or obstructions beneath the vehicle before lowering.
8
Do noT
operate the jack if damaged.
8
Do noT
work under the vehicle until axle stands have been correctly positioned.
8
Do noT
exceed the rated capacity of the jack (1.5tonne). When lifting a load of maximum capacity or close to
it, it is recommended that the effort be reduced by the use of assistance during this operation.
8
Do noT
adjust the safety overload valve.
8
Do noT
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
Do noT
allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
8
Do noT
top up hydraulic system with brake fluid. Use hydraulic jack oil only and use a qualified person to
maintain jack hydraulic system.
8
Do noT
allow untrained persons to operate the jack.
8
Do noT
use jack for purposes other than which it is designed.
8
Do noT
allow persons to ride on the jack.
9
When not in use store jack, fully lowered, in a safe, dry, childproof area.
2. inTroDucTion
Made primarily for the motor racing enthusiast, this jack weighs in at just 15.1kg. Mix of steel and aluminium not only makes this jack
lightweight but incredibly strong. large saddle with jacking pad. Rocket lift with twin piston design enables saddle to be brought up to jacking
point with minimal pumps. Features a lifting bar for fast, lightweight pick-up.
3. specificaTion
Model no: .........................................................RJAS1500.V2
Capacity: .................................................................. 1.5tonne
length: ....................................................................... 553mm
Maximum Chassis Height: .......................................... 134mm
Maximum Saddle Height: ........................................... 360mm
Minimum Saddle Height: .............................................. 90mm
nett Weight: ................................................................ 15.1kg
4. seT-up
4.1.
aDDinG HyDraulic fluiD
4.1.1.
Remove the Fill Screw.
Do noT
remove or loosen Safety Valve Cover Screws.
4.1.2.
Add high grade hydraulic fluid (sold separately) slowly until the fluid reaches 1/4″below the top of the Fill Port. (Fig.2).
note:
Do noT
touch the Handle when adding hydraulic fluid.
4.1.3.
Replace Fill Screw.
RJAS1500.V2 Issue 1 09/10/18
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear safety
footwear
