AIR IMPACT WRENCH 1” SQ. DRIVE TWIN
HAMMER
MODEL NO:
SA6008
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
i
9
Follow all workshop safety rules, regulations, and conditions when using wrench.
WARNING!
Disconnect from air supply before changing accessories or servicing.
9
Maintain the
wrench in good condition and replace any damaged or worn parts.
Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Only use impact sockets which are specifically designed for use with an impact wrench.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
WARNING!
Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we
recommend you wear suitable respiratory protection.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
8
DO NOT
use the wrench for a task it is not designed to perform.
WARNING! DO NOT
use wrench if damaged or thought to be faulty. Contact local Sealey stockist.
8
DO NOT
use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT
carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT
operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
carry wrench with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
Lightweight handling and heavyweight power. Features twist control at back of tool for simple choice of speed and direction. Composite
housing with soft grip and side handle helps reduce vibration and chill. Handle exhaust reduces noise level. Powerful twin hammer
mechanism gives high torque output suitable for commercial and agricultural use.
3. SPECIFICATION
Model No:
.................................................................
SA6008
Drive: ............................................................................ 1” Sq
Maximum Torque:......................................2200lb.ft(2970Nm)
Breakaway Torque: ...................................2500lb.ft(3375Nm)
Free Speed: .............................................................5500rpm
Air Consumption: ........................................................ 7.5cfm
Operating Pressure: ...................................................... 90psi
Air Inlet Size: .............................................................1/2”BSP
Weight: .......................................................................... 5.7kg
Noise Power/Pressure: .................................... 114/103dB(A)
Vibration/Uncertainty: ..................................... 20.42/1.59m/s²
4. PREPARATION
WARNING!
Ensure the air supply is clean and does not exceed 90psi while operating the wrench. Too high an air pressure and/or
unclean air will shorten the product life due to excessive wear, and may be dangerous, causing damage and/or personal injury
4.1.
AIR SUPPLY
Recommended hook-up procedure is shown in fig.1.
4.1.1.
Ensure wrench air valve (or trigger) is in the “off” position before connecting to the air supply.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3.
Drain the compressor air tank daily. Water in the air line will damage the wrench.
4.1.4. Clean compressor air inlet filter weekly.
4.1.5.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4” I.D. and fittings must have the same inside dimensions.
SA6008 Issue 1 01/05/19
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear protective
gloves
Wear eye
protection
Wear face
mask
Wear ear
protection
Wear protective
clothing
Wear safety
foorwear
