INSTRUCTIONS FOR
SMD LED LEAD LAMP
MODEL NO:
ML9230V
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
If the lamp is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING!
Disconnect lamp from mains power before performing any maintenance.
8
DO NOT
shine lamp directly into your, other person’s or animal’s eyes.
8
DO NOT
allow children to use the lamp.
9
Maintain the lamp in good condition.
8
DO NOT
use the lamp if the lamp if damaged.
9
When not in use store the light in a safe, dry, childproof location.
WARNING!
Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using this light.
9
Wear eye protection. A full range of safety equipment is
available from your Sealey stockist.
9
Wear suitable clothing to avoid snagging.
8
DO NOT
wear jewellery and tie back long hair.
9
Account for all tools being used and
DO NOT
leave them in or near the engine.
WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions
and
situations that may occur. It must be understood that common sense and caution are factors which must be applied by the
operator.
2. INTRODUCTION
High output illumination with even spread. SMD LED’s lower power consumption, saving on energy costs and a high shock resistance and life span.
Supplied with 5mtr power cable. Ideal for professional garage/workshop.
M
L9230V | Issue: 1 26/04/17
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
Recommended fuse rating
13 Amp
