background image

© Jack Sealey Limited

    Original Language Version 

INSTRUCTIONS FOR:

CORDLESS POLISHER/SANDER

 

14.4V 2Ah LITHIUM ION  

2 BATTERIES 40MIN CHARGER

MODEL NOs: 

CP6005, CP6015 (BODY ONLY)

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.  USE THE PRODUCT 

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL 

INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions 

and maintained properly, give you years of trouble free performance.

Refer to Instruction

Manual

Wear Eye 

Protection

Wear Ear Protection

Wear Protective

Gloves

Charger:

 Indoor 

Use Only

1.1.

  ELECTRICAL SAFETY.  

 

WARNING!

 It is the owner’s responsibility to read, understand and comply with the following electrical instructions:

 

You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current    

 

Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device)

 

is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB. 

 

You must

 also read and understand the following instructions concerning electrical safety.

1.1.1. The 

Electricity At Work Act 1989

 requires all portable electrical appliances, if used on business premises, to be tested by a qualified   

 

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The 

Health & Safety at Work Act 1974

 makes owners of electrical appliances responsible for the safe condition of the appliance and  

 

the safety of the appliance operator. 

 

If in any doubt about electrical safety, contact a qualified electrician.

 

Ensure that the charger and cable are inspected for wear and damage, to ensure they are safe before connecting to the mains power   

 

supply. If worn or damaged 

DO NOT

 use, replace immediately or contact a qualified electrician.

 

DO NOT

 use worn or damage cables, plugs or connectors. Have any faulty item repaired or replaced 

 

immediately by a qualified electrician. When an ASTA/BS approved UK 3 pin plug is  

 

 

 

damaged, cut the cable just above the plug and 

dispose of the plug safely.

 

 

Ensure that the double insulated charger is correctly connected via a three-pin plug, as follows:

 

a)

 Connect the Brown live wire to live terminal ‘L’.

 

b)

 

Connect the Blue neutral wire to the neutral terminal ‘N’.

 

c)

 After wiring, check that there are no bare wires, that all wires have been correctly connected, 

 

that the cable outer insulation extends past the cable clamp and that the clamp is tight. 

 

Note that the earth pin ‘E’ remains unconnected.

 

Check cables are always protected against short circuit and overload.

1.2.

  BATTERY SAFETY.

 

Charge battery prior to first use. The battery pack will have been shipped in a low charge state.

 

Use only the charger provided to charge the polisher battery.

 

DO NOT

 charge battery when room temperature is below 50°F (10°C) or above 104°F (40°C).

 

DO NOT

 attempt recharging the battery by means of a generator or a DC power source.

 

DO NOT

 short-circuit the battery by linking both terminals with conductive materials.

 

DO NOT

 store the battery (or wrench) in locations where the temperature may exceed 104°F (40°C).

 

 

DANGER! DO NOT attempt to dismantle the battery pack. For safety and environmental reasons DO NOT discard in domestic  

 

waste or by burning. ONLY discard or recycle according to local authority regulations.

 

WARNING! DO NOT

 

allow a leaking battery to contact your person. If you come into contact with battery liquid take the following  

 

immediate action:

 

a) Skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.

 

b) Eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.

1.3.

  BATTERY CHARGER SAFETY INSTRUCTIONS.

 

WARNING: DO NOT

 

use the charger to charge any battery other than that supplied for the polisher. Other types of batteries may  

 explode.

 

All mains electrical supply safety features must be followed as described in 1.1. above.

 

Disconnect the charger from the mains power supply when not in use. 

 

Important:

 Check that the voltage marked on the charger is the same as the power supply to be used.

 

DO NOT

 pull or carry the charger by the power lead, or pull the plug from the mains socket by the power lead.

 

DO NOT

 use any other type of charger.

 

DO NOT

 try to open or dismantle the charger.

 

DO NOT

 get the charger wet, or use in wet, damp conditions (for indoor use only).

 

DO NOT

 operate the charger if it or the battery is damaged.

 

DO NOT

 insert foreign objects or material into the hole reserved for the battery.

 

DO NOT

 force the battery into the charger. The battery will only fit one way to ensure correct polarity alignment.

 

DO NOT

 charge a second battery immediately. Consecutive charging will overheat the charger. Allow the unit to cool for 15 minutes 

 

before charging the next battery.

 

Store the charger in the same manner as the battery, see section 1.2.

 1.  SAFETY

Recommended Fuse 

Rating: 3A

  CP6005, CP6015  Issue: 1 - 28/02/17

 Wear a mask

Reviews: