![background image](http://html.mh-extra.com/html/sealey/bj10le/bj10le_manual_1225269001.webp)
BOTTLE JACK
10TONNE LOW ENTRY TELESCOPIC
MODEL NO:
BJ10LE
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
9
9
Inspect and lubricate the jack regularly to ensure it is in good working order.
DO NOT
use the jack if damaged or a fault is suspected.
Check chapter 6 troubleshooting. If necessary, repair or replace damaged parts immediately.
9
9
9
Use authorised parts only, the use of unauthorised parts may be dangerous and will invalidate your warranty.
9
9
9
Ensure the jacking area is clean and tidy and free from unrelated materials and there is adequate lighting.
9
9
9
Use jack on level and solid ground, preferably concrete.
Avoid tarmacadam since the jack may sink in
.
9
9
9
Park the vehicle and apply hand brake; if automatic, place in Park (P) mode. Switch off the engine, and place chocks under the wheels.
9
9
9
Ensure minimum distance of 0.5m between vehicle tilt and static objects such as doors, walls, etc.
9
9
9
Ensure all persons are out of the vehicle before jacking.
DO NOT
enter vehicle whilst it is supported on the jack or axle stands.
9
9
9
Check vehicle weight and recommended lifting points by referring to the vehicle owner’s manual. Ensure the lifting point is not corroded.
9
9
9
Check jack saddle is centred and stable on lifting point, (off-centre loads can slip). Position jack to avoid operating it from under vehicle.
9
▲
9
DANGER!
Use the jack for lifting only,
NOT
for supporting the lifted load. ALWAYS USE PROPERLY RATED AXLE STANDS.
9
9
9
Keep hands etc. clear of moving parts during raising and lowering of the vehicle.
9
9
9
Use properly rated axle stands under the vehicle before proceeding with any task.
9
▲
9
DANGER!
Roadside wheel change is hazardous.
Be extra vigilant.
You may not be able to avoid jacking on tarmacadam. Get everyone
out of vehicle.
NEVER
go under vehicle, traffic may cause vehicle to rock. Use hazard warning lights. If in doubt call professional help.
9
9
9
When changing a wheel, slightly loosen wheel nuts prior to jacking vehicle. Screw wheel nuts back before lowering vehicle.
9
9
9
Use a competent person to lubricate and maintain the jack.
9
8
9
DO NOT
exceed the rated capacity of the jack, and
9
DO NOT
operate the jack beyond its maximum pump stroke.
9
9
WARNING!
DO NOT
allow the vehicle to move during jacking.
DO NOT
start the engine when vehicle is jacked up.
9
8
9
DO NOT
jack a vehicle if it may result in the spillage of fuel, battery acid, or other dangerous substances.
9
8
9
DO NOT
place any part of your body under vehicle whilst supported by jack. Wait until properly rated axle stands have been correctly
positioned.
9
8
9
DO NOT
use jack to support extensions or cradles.
DO NOT
modify jack in any way.
DO NOT
use the jack for any other purpose than
that for which it is designed.
9
8
9
DO NOT
top up jack hydraulic system with brake fluid. Use hydraulic oil only, and
DO NOT
adjust the safety overload valve.
9
9
9
Ensure there are no persons or obstruction beneath the vehicle before lowering.
9
9
9
Clean, and stow the jack securely, with the ram in the down position. Ensure stowage area is dry.
9
9
WARNING!
Remember,
It is
very dangerous
to get under a vehicle supported by a jack
even
if additional supports are used.
8
DO NOT
go under a vehicle without the support of properly rated axle stands.
NOTE:
Seek advice before jacking caravans or trailers.
2. INTRODUCTION
Fitted with overload valve. Base and reservoir machine welded
for increased strength and reduced chance of leakage. Threaded
pump assembly allows for easy disassembly and maintenance.
Supplied with 4pc handle. Fitted with carrying handle. Service kit
readily available.
IMPORTANT SAFETY WARNING: ALWAYS USE AXLE STANDS
Please remember a jack is a lifting device and is not designed to
support a load. Never get underneath a vehicle supported only
by a jack - your life is at risk. We stock a comprehensive range of
axle stands - please see relative section for full details.
3. SPECIFICATION
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . .
BJ10LE
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Tonne
Minimum Height:. . . . . . . . . . . . . . . . . . . . . . . .128mm
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . .223mm
Hydraulic Lift: . . . . . . . . . . . . . . . . . . . . . . . . . . .95mm
Screw Extension: . . . . . . . . . . . . . . . . . . . . . . . . . . N/A
BJ10LE Issue: 2 (H,F, 2) - 10/06/19
Original Language Version
© Jack Sealey Limited
Refer to
instructions