![background image](http://html.mh-extra.com/html/savant/sha-b7cr-series/sha-b7cr-series_quick-reference-manual_1203614001.webp)
SHA-B7CRxx-00 | 009-1651-00 | 180424
Copyright 2018 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
| 508.683.2500
1 of 2
HELPFUL!
Before starting the mounting process, review the diagram below to ensure a trouble free install.
The shade mount in the SHA-B7CRxx corner shade mount kit is a floating/outside type mount for the idler side (opposite drive motor) of a
Savant shade installation. The mount has a 45° bevel with a slot cut in the bevel so it can be joined together with any of the other corner type
mount using the angled bracket included (angled bracket is included in the SHA-B7CRxx and SHA-B8CRxx shade mount kits). The shade mounts
from the SHA-B7 and SHA-B8 shade corner mounts kits are typically installed where two windows meet each other to form either an inside or
outside 90° angle. As shown in the Box Contents image below, the Tube End Plug included with the kit, slides into the hole in the center of the
mount. The shade mount in the SHA-B7CRxx kit is a floating/outside type mount and is installed using the included shade mount sleeve and 2
inch hanger bolt. Before installing this mount (idler side), Savant recommends that a drive side shade mount be installed first and then used as a
reference point for when installing this mount.
Vertical Mount
– Install the shade mount so the center point of the mount is installed at
least
1
³/₄
inch (minimum) from any obstructions.
– To aid in the installation of the shade mounts, a template (SHA-INSTEMP-
xx) is available. This template contains all the holes and spacing required
to mount any of the shade mounts.
– To reduce marking up the walls, it is recommended that painters tape be
used whenever drilling is involved.
1.75 in.
(minimum)
Assemble Shade Corner Mounts
Box Contents
Hanger Bolt
Shade Mount Sleeve
3/32 in. Hex Screw
90° Angled
Joiner Bracket
Tube End Plug
(Female)
Front View
SHA-B7CRxx
Shade Mount
Flat Head Screw
(1) Shade Mount - Floating/Outside Type Corner Mount
(1) 90° Angled Joiner Bracket
(1) Shade Tube End Plug (female)
(1) 2-inch Hanger Bolt
(1) 1 inch Shade Mount Sleeve
(1) #6 x 1
1/2
in. Flat Head Screw
(1) Quick Reference Guide (this document)
The mounts in the SHA-B7CR, SHA-B7CL, SHA-B8CR, and SHA-B8CL kits are all corner shade mounts and utilize a 90° angled joiner bracket to
join any two of these corner mounts. Once the shade mounts are joined together, they form a 90° angle that can be used in most inside or out-
side corners. The steps below describe how to join the shade mounts in the SHA-B7CRxx and SHA-B7CLxx shade mount kits but these instruc-
tions can be used to join any of the other corner type shade mounts.
1. Grab the corner shade mount and 90° angled joiner bracket from a SHA-
B7CRxx corner shade mount kit.
HELPFUL!
Angle brackets are supplied with only the SHA-B7CRxx and
SHA-B8CRxx shade mount kits.
2. Slide the joiner bracket into the slot in the shade mount. Slide bracket into
the mount until it sits flush with the top of shade mount.
Slide bracket into
shade mount. Slide
downward until
bracket is fully seated
Angled part of
the shade mount
Outside view
of the SHA-B7CR
Slot in shade mount
For Product Info
Savant® Shade Corner Idler Right (SHA-B7CRxx-00)
Quick Reference Guide