Satellite AV GEOSATpro GS120 DiSEqC Manual Download

Page: 1 / 10

Satellite AV, LLC

lite AV, LLC

8801 Washington Blvd., Suite 101

8801 Washington Blvd., Suite 101
Roseville, CA 95678

Roseville, CA 95678
888-483-4673

888-483-4673
Local 916-677-0720

Local 916-677-0720
Fax 916-677-6228

Fax 916-677-6228

Installation Guide:

GEOSATpro

GS120 DiSEqC Motorized Satellite Dish Mover

GEOSATpro

GS120 DiSEqC Motorized Satellite Dish Mover

Items needed for installation:

DiSEqC / USALS Compatible GEOSATpro GS120 Motor or Similar

Fortec Star Mercury II / Visionsat IV-200 Satellite Receiver with USALS

Assembled 76cm – 1.2 Meter Dish

LNBF (KU-Band Standard Type)

5’ Coax Jumper

Portable TV with cables for connecting to the satellite receiver output

Satellite aiming Calculator is available at:

http://www.geosatfinder.com

Available channels and broadcaster information can be found at:

http://www.lyngsat.com

What to learn more about Free to Air Satellite and share your FTA experience with a helpful and
friendly group? Visit:

http://www.satelliteguys.us

Assemble the motor using the motor assembly manual. Securely tighten the bolt that attaches

the post to the motor with an Allen wrench. A loose bolt will cause the dish to slip out of position.

Summary of Contents for GEOSATpro GS120 DiSEqC











Search results

Summary of Contents for GEOSATpro GS120 DiSEqC

Reviews:

Related manuals for GEOSATpro GS120 DiSEqC

Brands by name

Popular brands

Satellite AV GEOSATpro GS120 DiSEqC, Manual

Search results

Summary of Contents for GEOSATpro GS120 DiSEqC

Reviews:

Related manuals for GEOSATpro GS120 DiSEqC

Brands by name

Popular brands