background image

WEA302i/303i/303e Installation Manual

Status LED

Ethernet port

DC input

Console port Reset switch

Introduction

What is WEA302i/303i/303e? 

The WEA302i/303i/303e is AP for Samsung WE wireless LAN. 
It connects the UE that supports wireless LAN such as a smart phone, tablet PC, or notebook to a 
wired network. The WEA302i/303i/303e supports the following features:
- IEEE 802.11a/b/g/n standard
- Power over Ethernet (PoE) IEEE 802.3af 
- WEA302i: 2 × 2 MIMO (Multiple Input Multiple Output)
- WEA303i/303e: 3 × 3 MIMO (Multiple Input Multiple Output)
- Wireless LAN through both 2.4 GHz and 5 GHz ISM bandwidth 

Component 

After unpacking the WEA302i/303i/303e, check whether all of the following items are included.

WEA302i/303i

WEA303e

Common merchandise

Ceiling bracket

Two ceiling clips

Three M3 × L6 screws 

(including 1 spare)

Installation Manual

Wall mount bracket installation set (sold separately)

Wall mount bracket

Security torx 

(T10) screw

Four plastic  

anchors

M4 × L28 

Four screws

RJ45 gender

- It is recommended to keep all the packing materials and box.
- The wall mount bracket installation set, power adaptor, and external antenna for WEA303e are sold 

separately.

- The cable hole guide seat is provided separately.

This manual describes the configuration of Wireless Enterprise WEA302i/303i/303e and how to 
install WEA302i/303i/303e.

The instruction on how to install is described based the WEA302i/303i model, and the instruction   
on how to install the WEA303e model is same except for the installation of an external antenna.

Name and Function

Dust covers are installed on a power port (DC 12 V/2.0 A) and console port (CONSOLE).
Remove the cover before use.

Interface

Interface

Description

Status LED

Displays the status information of WEA302i/303i/303e with LED. 

DC input

Used when a power adaptor is used for power supply.

Ethernet port

Supports 1000 BASE-T Gigabit Ethernet and PoE IEEE 802.3af standard.

Console port

Checks the operation status of WEA302i/303i/303e and used for CLI input.

Reset switch

Used to restart the WEA302i/303i/303e.

Status LED

LED

Status

Description

System start status

White On

Initial LED status

Blue On

Device reset and test in progress

Red On

Booting failure (Device reset failure)

Provisioning status

Repeated Red, Green, and Off

Connecting APC (network link normal status)

Blinking green

Connecting CAPWAP link (APC server normal connection status) 

Normal operation 
status

Green On

When there is no connected wireless UE

Blue On

When there is a connected wireless UE 

Upgrade

Blinking blue

Upgrading software 

Fault status

Blinking red

Abnormal network link (checking link status after disconnection 
or re-connection)

Blinking orange

IP address conflict

Blinking violet

Dynamic IP Address allocation failure

Blinking bluish green

Fixed IP check failure

Repeated Red, Blue, and Off

Wireless interface fault status 

Installation

The WEA302i/303i/303e can be installed on a ceiling or wall. Please check whether all the components 
are included before installation.

Before Installation 

Safety Requirements

If the below safety warnings are not properly observed, it may cause a risk.
Make sure to be informed for safe use.

- There is an electrical risk with the product. Make sure that the power is turned off during installation. 

Do not proceed with the installation when there is current leakage. Otherwise, this may cause serious 

personal injury.

- Wear anti-static gloves or take an appropriate action to prevent ESD during product handling.
- Do not connect a phone line connector to an Ethernet port. This may damage the product.
- This product must be connected to a power supply in compliance with IEEE 802.3af or to a limited power 

supply in compliance with IEC60950.

- This product must be installed or removed only by appropriately trained service personnel.
- This product is operating in the Safety Extra Low Voltage (SELV) state according to IEC60950.
- All the connected equipment including this product must be installed inside of the same building.   

For more information, refer to the Environment A of IEEE 802.3af standard. 

Installation Instructions

The below instructions must be observed during installation. 
- The system must be easily accessible for product installation, cable connection, or maintenance.
- The PoE LAN cable must be installed always away from an electrical interference source such as  

power line, fluorescent light, radio, or transmitter.

- The PoE LAN cable must be CAT 5E or higher.  
- If it is not easy to use PoE, a power adapter (sold separately) can be used. 

The 3-pin (including ground) power consent that supplies 100-240 V AC, 50-60 Hz must be located 
within 2 m from equipment and the power must be supplied through an independent circuit breaker. 
It is recommended to use equipment that uses a filter or surge breaker.

- The ambient temperature must be maintained between 0'C and 45°C. The ambient humidity,  

in absence of air pressure change, must be maintained between 10 % and 90 %.

Installation on a Ceiling

If the WEA302i/303i/303e is incorrectly installed on the ceiling, the product may drop onto a person or 

equipment. Therefore, make sure to fix it firmly.

1.  

Place a ceiling bracket by making its convex part  
upward and align a ceiling clip to the groove of the  
ceiling bracket and insert the clip to the position that  
is shown in the figure.  
Push and move the ceiling clip according to the  
T-bar size of the ceiling.

2.  

Fix the ceiling clip to the ceiling bracket by tightening  
one M3 × L6 screw to either of the two holes.  

 

If the T-bar size of ceiling is 15 mm, 24 mm, or  

38 mm, you can check a fixing position where a  

ceiling clip can be fixed on the floor of ceiling  

bracket.  

If the T-bar size is unknown, tighten the two ceiling  

clips using one screw each in the step 4.

3.  

Align the ceiling clip on the other side to the groove  
of ceiling bracket and insert the clip.  

Reviews: