Quick Guide Installation
Model: RT510 / RT510RF / RT510TX / RT510BC / RXRT510
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Introduction
The RT510 thermostat will switch your heating system on or off, as needed, in accordance
with the temperature set by you. The RT510 series includes the following products:
• RT510 for wired applications
• RT510RF (R RXRT510) for wireless applications
• RT510TX for wireless application, using 5 x 5 receiver
• RXRT510 for wireless application using 5 x 5 transmitter
• RT510BC for wireless application
Go to www.salus-manuals.com for the full PDF version of the manual.
Product Compliance
EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU and 2011/65/EU. Please check
www.saluslegal.com for the full information.
Safety Information
Use in accordance with the EU and national regulations.
For indoor use only.
Keep your device completely dry.
This product must be installed by a competent person and in accordance with all the
EU and national regulations.
Installation
Installation
Button Functions RT510 and RT510TX
Pairing the RT510TX with the Receiver/Boiler Controller
Installer Mode
Dip Switch Settings
RT510 and RT510RF Quick Guide
RT510 Thermostat
Terminal
Description
Backplate
Common Terminal
1 (COM)
2 (NC)
Switched Live OFF
3 (NO)
Switched Live ON
RESET
SELECT
+Hr
SET
RESET
+Hr
SELECT
SET
RESET
+Hr
SELECT
SET
TEST / PAIRING
SELECT
+Hr
SET
TEST / PAIRING
SELECT
+Hr
SET
TEST / PAIRING
SELECT
+Hr
SET
Insert the batteries and
wire up the device.
RT510RF (RXRT510)Thermostat and Receiver
RT510
RT510TX
ON
AUTO
OFF
MANUAL
Insert the batteries and wire up the receiver. After that please switch the
receiver ON. If you are using the RT510RF pack, the pairing between the
thermostat and the receiver is already done.
COM
NO
L N
Terminal
Description
Receiver Terminals
NO
COM
L
N
Switch Terminal
Common Switch Terminal
Mains Live (230VAC)
Mains Neutral
RT510BC (Boiler Controller)
Insert the batteries and wire up the boiler controller.
If you are using the
RT510BC pack, the pairing between the thermostat and the receiver is
already done.
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
N L 1 2 3 4
N L 1 2 3 4 5 6
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
NL
12
34
NL
12
34
56
N L 1 2 3 4
N L 1 2 3 4 5 6
N L 1 2 3 4
N L 1 2 3 4 5 6
1
2
3
4
Terminal
Description
Rear of controller
4 (NO)
3 (COM)
2 (L)
1 (N)
Switch Terminal
Common Switch Terminal
Mains Live
Mains Neutral
Boiler internal connections
The DIP switches are found on the rear of
your thermostat and can be used to change
the span (temperature accuracy) of your
thermostat from the default
+/-
0.5°C to
+/-
0.25°C and the programmes 5-2 or 24h.
Changing DIP Switch 2 may cause your boiler
to operate more frequently. The DIP switches
are located on the back of the thermostat.
24H
5-2
+/-0.25
+/-0.5
ON
1
2
Key
Function
+Hr
SELECT
SELECT
SET
SET
+
+
+
1. Press once to activate Frost Mode
2. Press for 3 seconds in order to activate Holiday Mode.
Press once to activate/deactivate Boost function
Press once to enter/exit Permanent Override function.
Increase button
Decrease button
Select the clock or programme settings
Press to confirm your settings
Press the buttons for 3 seconds to enter Installer Mode
Press the buttons for 3 seconds to enter Clock Settings
1. Press once to enter in Test Mode for RT510RF
2. Press for 3 seconds to enter/exit Pairing Mode for RT510RF
3. Press once to return to Factory Settings for the RT510
RESET
+Hr
SELECT
SET
3 Sec
3 Sec
3 Sec
Press the three buttons
together for 3 seconds.
dxx
Function
Parameter Description
Default
value
d01
Temperature display
increments
0.1 or 0.5
°
C
Select temperature display
increments
0.5
°
C
d02
Temperature /-3.0
°
C
Calibrate your thermostat
temperature
0.0
°
C
d03
Frost setpoint
5.0
-17.0°C
Set the Frost Point temperature 5.0
°
C
If you are using the RT510RF or RT510BC pack, the pairing between
the thermostat and the receiver/boiler controller is already done.
If you bought an RT510TX and RXRT510 separately then pair as follows.
Please make sure that the Receiver/Boiler Controller is set on Auto.
Begin the pairing process
TEST / PAIRING
SELECT
+Hr
SET
TEST / PAIRING
SELECT
+Hr
SET
TEST / PAIRING
SELECT
+Hr
SET
3 Sec
ON
AUTO
OFF
MANUAL
TEST / PAIRING
SELECT
+Hr
SET
Wait 9 minutes for the timeout
process to be complete.
End the pairing process
3 Sec
ON
AUTO
OFF
MANUAL
TEST / PAIRING
+Hr
SELECT
SET
TEST / PAIRING
+Hr
SELECT
SET
Test the pairing process
If you bought an RXRT510 or RT510TX and intend pairing with other
devices in the 5x5 range, please refer to the Receiver Units manual, or the
relevant manuals available at www.salus-manuals.com
Button Description for RXRT510 Receiver
Button Function
ON
The receiver is enabled, ready for use.
OFF
The receiver is disabled, will not function.
AUTO
The receiver will switch on and off automatically,
as operated by the thermostat.
MANUAL
Providing ON is selected,the receiver will switch
on continuously, overriding the thermostat.
Button Description for RXBC605 Boiler Controller
Button Function
SYNC
The boiler controller will be syncronised with the
thermostat.
AUTO
The receiver will switch on and off automatically,
as operated by the thermostat.
MANUAL
Select in the event of thermostat failure to switch
boiler on continuously, overriding the thermostat.
ON
AUTO
OFF
MANUAL
