1
Drum stand
Drum sound module / Pads / Others
For a left-handed setup
3
4
2
Assembly procedure
5
Connection procedure
Setup Guide
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the leaflet “USING THE UNIT SAFELY,” “TD-07 Owner’s Manual,” and the Setup Guide).
After reading, keep the document(s) where it will be available for immediate reference.
Check the included items
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
* This package does not include a kick pedal. Use with a commercially available kick pedal.
* When checking the
items included with the
drum stand, refer to
“MDS-Compact Owner’s
Manual.”
The setup described in this guide is for right-handed players. To set up for a left-handed player,
reattach the components as follows.
5
Exchange curved pipes (L) and (R), and straight pipes (L) and (R), left-for-right.
5
Attach the mount holder (L) to the curved pipe (L).
5
Attach holder (C) and the snare pipe to the right side.
5
Exchange the pads and cymbals with their attachment mounts left-for-right.
5
Exchange the drum sound module with its sound module mount left-for-right.
9
When you’ve finished making connections, turn on the power as described in the “TD-07 Owner’s
Manual,” and verify that you can hear sound.
This completes assembly and connections.
Attach the parts
Connect the pads to the drum sound module (TD-07)
Assemble the drum stand
Assemble the stand as the “B” type (for ride cymbal), following the steps in the “MDS-Compact Owner’s
Manual.”
* The tip of the mount is sharp. Handle it with care.
* When setting up or storing the stand, be careful not to pinch the fingers you use to
handle the stand.
Connect the AC adaptor and
speakers
Connect the AC adaptor, headphones, or speakers as described in the “TD-07
Owner’s Manual.”
* To prevent malfunction and equipment failure, always turn down the volume, and turn off all the
units before making any connections.
Connect the cables as shown in the illustration.
* The drum stand assembly procedure is for right-handed players.
If you want to set up the stand for left-handed players, refer to
“Assembly for left-handed players” below.
* Adjust the position and height of the pads and pedals according
to your height and tastes, so that they are easy to play.
* Insert the plug firmly,
making sure it’s all
the way in.
1.
Connect the connection cable to the
drum sound module as shown in the
illustration below.
Insert the connector all the way, then
turn the knobs to fasten it securely.
2.
Labels are affixed to the connection
cable to indicate the pads to be
connected. Make connections as
shown in the illustration at right.
CY-8
PDX-12
PDX-8
PDX-8
KD-10
CY-5
TD-07
PDX-8
(T1)
(T2)
(T3)
(SNR)
(KIK)
(HH)
(CR1)
CY-8
(CR2)
FD-9
(HHC)
CY-8
(RD)
CY-8
PDX-12
PDX-8
PDX-8
PDX-8
CY-5
KD-10
FD-9
TD-07
CY-8
TD-07KX
Use caution regarding the following to prevent
the drum stand from falling over.
5
Adjust the rod height so that no part of any
cymbal is higher than 1.2 meters (48 inches)
above the floor.
5
Attach the cymbal so that its center does
not extend toward the back beyond the
pipes of the stand (the pipes at the back of
the stand).
Adjusting the position of the cymbal
Attach the snare (PDX-12) and
toms (PDX-8)
Place the hi-hat control pedal (FD-9)
When using on the V-Drums mat,
noise eater, or carpet
When using on the floor
Anchor bolts
If you’re using this unit on a V-Drums mat, on a noise eater
(NE-10), or on carpet, extending the anchor bolts will secure
the unit in place, making it easier for you to perform.
* The tips of the anchor bolts are
sharp. Handle with care.
* When used on flooring, the
anchor bolts may damage the
floor.
1.2 m
(48 inches)
OK
Not OK
Attach the kick pedal
Install the kick pedal securely.
Cabling diagram for the connection cable
(As seen from the back)
* Fasten the cables so that they will not
obstruct your playing; use cable clips
and cable ties.
Make sure to wrap the cable ties
around the pipes.
CR1
T2
T1
HH
SNR
RD
TD-07
HHC
KIK
1.2 m (48 inches)
* To prevent the drum stand from tipping over, do not
position the stand leg pipes at the two ends more than
1.2 meters (48 inches) apart.
8
Hi-hat control pedal
(FD-9)
8
Cymbal pad for hi-hat
(CY-5)
8
V-Cymbal for crash/ride
(CY-8 x 3)
8
Connection cable
8
AC adaptor
8
V-Pad for tom
(PDX-8 x 3)
8
Setup Guide (this document)
8
Owner’s Manual set
8
Kick pad (KD-10)
8
V-Pad for snare
(PDX-12)
8
Drum sound module
(TD-07)
Remove the caps, remove holder (C) and the snare pipe, and
reattach them to the right side.
Cabling diagram for the connection cable
(As seen from the back)
Adjust the location
at which the KD-10 is
installed so that it’s at a
comfortable position for
playing.
After exchanging the curved pipes, attach
the holders so that the marks on the pipes
are visible through the gaps of the holders.
Mark
Straight pipe R (short)
Curved pipe R
(including the pad mount)
Straight pipe L (long)
Curved pipe L
Attach the hi-hat (CY-5)
Tighten the cymbal nut enough to prevent the pad
from wobbling when you strike it. Use the cymbal
nut and felt washer that are included with the stand.
“Roland” logo on the farther side
Cymbal nut
Felt washer
*
5
1
0
0
0
7
6
4
3
9
-
0
1
*
© 2021 Roland Corporation
8
Drum sound module
holder
8
Drum key
8
Cymbal mount (short)
CY-8
Attach the drum sound module (TD-07)
1.
Use the drum key to loosen the bolt A of the
drum sound module holder, then attach the
drum sound module holder to straight pipe
“L” (long) and tighten the bolt.
2.
Use the bolt B of the drum sound module
holder to attach it as shown in the
illustration.
Straight pipe
L (Long)
Bolt A
Drum sound module holder
Bolt B
Drum key
T3
Attach the crash cymbal (CY-8) and ride cymbal (CY-8)
“Roland” logo on the farther side
Cymbal nut
Felt washer
Stopper
(convex
portion)
* Use the cymbal nut and felt washer that are included
with the drum stand.
1.
Position the cymbal so that the stopper (convex portion)
of the cymbal mount is aligned with the concave portion
of the bottom of the cymbal.
2.
Tighten the cymbal nut enough to allow an appropriate
amount of sway.
CR2
MEMO
5
Attach the cymbal mount (short) marked with an asterisk as an additional part after you assemble the
drum stand.
5
The mount holder marked with an asterisk is not used on the TD-07KX. However, you may need it when
attaching a sound module aside from the TD-07, so keep it for later use.
Cymbal mounts
Cymbal mounts
Pad mounts
Cymbal mount
* Mount
holder
If the stand wobbles, loosen
this hand knob and adjust
the height.
* Cymbal mount
Attach this as an additional
part.
Remove this, as it is not used on
the TD-07KX.
NOTE
When handling the hi-hat control pedal, kick pedal, or cymbal pads, take care not to
pinch your fingers between movable parts and the main unit. If using this in a location
where children are present, be sure to provide adult supervision or guidance.
CR1
T2
T1
SNR
HHC
KIK
HH
TD-07
T3
CR2
RD
Loosen
Tighten
Pad mount
Loosen
Tighten
Pad mount
Knob
Label
