Richmond GTR207 User Manual Download

Page: 1 / 31

GTR207 Installation Manual:

Rev 1b

Low Voltage Sliding Gate Opener

User Manual

GTR207

WARNING

Instructions must be read before beginning installation. Please follow these instructions carefully, incorrect installation could

affect gate operation. If you require more information, please contact your local Richmond Wheel & Castor Co branch.

AU:

1300 474 246

NZ:

0800 61 71 81

International:

+613 9551 2233

For installation or troubleshooting assistance visit richmondau.com/gate-motor-support/

When mounting and positioning the motor ensure that the power cable is unplugged. The motor cover will need to be removed to mount

the motor to the mounting plate.

Please Note: This motor runs on 24VAC Power as standard but can also be operated by 24VDC Battery Backup or Solar Power.

Gate in closed position

Gate in open position

Viewed from inside the property

For accessories:

please refer to the relevant accessory manuals for instructions on wiring them to the GTR207 motor.

Summary of Contents for GTR207
































Search results

Summary of Contents for GTR207

Reviews:

Related manuals for GTR207

Brands by name

Popular brands

Richmond GTR207, User Manual

Search results

Summary of Contents for GTR207

Reviews:

Related manuals for GTR207

Brands by name

Popular brands