background image

04/09/15

FOR YOUR SAFETY

What to do if you smell gas:

 

Do not try to light any appli-

ance

  Do not touch any electri-

cal switch: do not use any 

phone in your building.

  Immediately call your gas 

supplier from a neighbour's 

phone. Follow the gas sup-

plier's instructions.

  If you  cannot reach your 

gas  supplier,  call  the  fire 

department.

WARNING:  

Improper installation, adjustment, altera-

tion, service or maintenance can cause 

injury or property damage. Refer to this 

manual. For assistance or additional in-

formation consult an authorized installer, 

service agency or the gas supplier.
FOR YOUR SAFETY

Do not store or use gasoline or other flam

-

mable vapours and liquids in the vicinity of 

this or any other appliance.
Installation and service must be performed 

by an authorized installer, service agency or 

the gas supplier.

PLEASE KEEP THESE INSTRUCTIONS 

FOR FUTURE REFERENCE

Owners &

Installation

Manual

LISTINGS AND CODE APPROVALS

These gas appliances have been tested in 

accordance with AS4553, NZS 5262 and 

have been certified by the Australian Gas 

Association for installation and operation 

as described in these Installation and 

Operating Instructions.

Your unit should be serviced annually 

by an authorised service person.

918-646d

Models: FG39-NG1

 FG39-LPG1

Freestanding Gas Stove

Summary of Contents for FG39-LPG1





































Reviews: