User Manual
www.red-pro.com
Note
Always verify that the unit is operating properly before use.
REDPRO WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND
INCLUDING, BUT NOT LIMITED TO, COMPENSATION
OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF
THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR
AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER
Page 1
Page 5
Page 3
Page 6
Page 2
Page 4
If you want to know more about REDPRO Products please visit our
website:
www.red-pro.com
Before operating the unit, please read this manual thoroughly and retain it for future reference.
Important Safety Instructions
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Overview / Features
The PB-D100V/A Battery Pack uses Lithium-Ion Battery Cells.
Use the PB-D100V/A Battery Pack only with equipment whose Operation Manual/Operating
Instructions recommends its use.
Caution On charging
• The battery pack can be charged within a temperature range of 0°C to 40°C (32°F to 104°F).
However, we recommend charging within a temperature range of 10°C to 30°C (50°F to 86°F) to
ensure optimum battery performance.
• The battery pack discharges naturally over time. To prolong the life of the product, it is
recommended that you fully charge the battery pack before using it. For details on the charging
procedure, refer to the Operation Manual/Operating Instructions supplied with the battery charger.
• The battery pack may become warm in use or while being charged. This is normal.
You can use
original
REDPRO
charger RP-DC
8
0 to charge the P
B
-
D100V and PB-D100A
Battery Pack.
Battery Pack Operating Instructions
Specification
POWER METER - LED Indicator
Testing the capacity of the Battery pack:
-
The remaining capacity is indicated by a four-step
LED Dysplay
- Press the Check Button and the remaining Capacity of the Battery Pack will be displayed on LED
Dysplay ( more than 80%, 60%, 40%,below 20%)
100% - 80% 80% - 60% 60% - 40% 40% - 20%
Full Charge Low Charge
- If the Battery Pack is instilled on the Camcorder with function of powering the camera, the LED
Power Dysplay may not show exact capacity status of the battery pack.
- When only one LED indicates please recharge the battery as soon as possible.
4 LED Display
Check Button
Professional Digital
Battery Pack
PB-D100V & PB-D100A
D-Tap 14.8V , 8A Power Output
Caution on Use
USB-Tap 5V , 1A Power Output
DC Power Jack - Charging input
- The D-TAP DC Output socket can be used as
14.8V DC
output, or DC charging input
- Open the rubber protective cover with
D-TAP
sign on it.
- Plug in the D-Tap lead for DC output, or for charging the battery .
-To keep D-Tap socket away from dust close the D-Tap output with rubber protective cover
The Maximum constant currency that Battery provide during DC 14.8V Power Output is
5A
Battery offers 5V/1A USB Power Output for charging mobile phones and all other units on USB.
- Open the rubber protective cover with
USB
sign on it.
- Plug in the USB lead and connect with device that need to be charged.
- Press the CHECK Button to switch on the USB charging.
- To keep USB socket away from dust close the USB output with rubber protective cover.
Battery is provided with DC Power Jack input 5.5mm x 2.1mm.
This power Jack input is designed only for charging the battery with REDPRO Battery Charger
RP-DC80
- Open the rubber protective cover with
DC
sign on it.
- Plug in the Extension adaptor Cable RedPro model
RPC-DC8
, connect the extension cable with
RedPro Charger
RP-DC80
and the Charging process of the Battery start automatically.
- To keep DC socket away from dust close the DC power input with rubber protective cover.
NOTE:
The positive and negative ( + / - ) orientation in the DC Power input Jack is not organized by
standard orientation.
+ 16.8V (+) Positive
- 16.8V (+) Negative
+
-
• Never short-circuit the battery pack terminals.
• Never attempt to open the battery pack.
• Avoid mechanical shock.
• Please consult the store where you purchased this battery pack or your sales representative before
using the battery pack in a product whose Operation Manual/Operating Instructions does not
explicitly state that the battery pack can be used, or before using the battery pack in conjunction with
another power supply. In appropriate use of the battery pack may result in unit misoperation.
• The internal impedance of the battery pack increases as the temperature drops to 5°C (41°F) or
below. This may result in a shorter operating time or the failure of the component to which it is
connected to turn on. This phenomenon occurs more frequently in battery packs that have been
charged many times than in new ones.
• The performance and operating time of the battery may drop under cold conditions. When this
happens, do the following to extend the operating time of the battery pack:
- Best Charging Performances is provided with
REDPRO
charger
model
RP-DC
8
0
within a
temperature range of 10°C to 30°C (50°F to 86°F).
• Large discharge amount may expedite deterioration of battery pack’s internal cells. To prevent this,
use the PB-D100V or BP-D100A with discharger amount of about 5 A or less.
• The maximum discharge amount is
8
A
for the PB-D100V or PB-D100A at 23°C (73°F). Continuous
use at levels beyond the maximum discharge level may cause the protection circuit to shut off the
current to protect the internal battery cells.
Caution On storage
• Never expose the battery pack to rain or moisture.
• Keep away from children.
• Never expose the battery pack to temperatures above 60°C (140°F). Store the battery pack in dry
place at temperatures between 0°C to 23°C (32°F to 73°F).
• If the battery pack is to be stored for a short period (approximately more than 24 hours and a month
or less), discharge the battery pack to 90% of its full capacity to prevent deterioration of battery pack’s
internal cells.
• When storing the battery pack for an extended period (more than a month), it is recommended that
you discharge the battery pack to about 50% of its full capacity. (The two LED light up) While the
battery pack is stored, charge it until the capacity reaches 50% once in 6 months.
• If the battery pack terminals become soiled, clean them with a soft cloth.
To the purchasers of the PB-D100V and PB-D100A Battery Pack
The RP-D100V / PB-D100A Lithium-ion Battery Pack has a rated capacity no more than 100 Wh.
It
CAN BE and it is totaly safe to be TRANSPORTED by AIR according to the IATA
Regulations, as it is non-hazardous lithium-ion battery. Related laws and regulations are,
however, subject to change. For detailed conditions regarding the transport of battery packs,
please consult your respective air transport company.
Battery life
• Battery life may be shortened due to storage or operation in high temperatures, storage with its
full capacity, and frequent use.
• Renew the battery pack when the operating time with a completely charged battery pack
becomes noticeably short or all LEDs flash because the self-diagnostics function has detected the
end of battery life. If a Battery pack is deteriorated, all LEDs may not light when the CHECK button
is pressed just after charging is completed.
Self-diagnostic function
When an abnormality is detected, all the LEDs flash. If this happens, stop using the battery pack
immediately. Once the LEDs start flashing, the battery pack cannot be recharged
This product with the CE marking complies with the EMC Directive issued by the Commission of
the European Community. Compliance with this directive implies conformity to the following
European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following Electromagnetic Environments:
E1 (residential),
E2 (commercial and light industrial),
E3 (urban outdoors),
E4 (controlled EMC environment, ex. TV studio).
WARNING
• Batteries shall not be exposed to excessive heat such as sunshine. fire or the like.
• Once the protection circuit has tripped, the battery pack will not return to normal automatically.
To cancel the effect of the protection circuit, you must charge the battery pack with charger
dedicated to the lithium-ion battery packs.
Battery Pack Type:
Mount Type:
Power Meter:
Internal Battery Cells
Maximum Voltage:
Nominal Voltage:
Max. Constant Output
Battery
Capacity:
USB
Output:
D-Tap
DC Output:
DC Jack
Input:
Charging Time:
Operating Temperature:
Mount material:
Dimensions (W/H/D)
Net Weight:
Lithium-ion Rechargeable Battery
PB-D100V ( V-Lock) ; BP-D100A ( Anton Bauer)
4-level LED Power indicator
Samsung SDI High Quality 18650 x 12
17,1 V DC
14.8 V DC
8A / 100W ( max )
97.68 Wh / 6600mAh
5V, 10W / 2.1A ( max ) - Dust Protection Cover
14.8V, 50W / 4 A ( max ) - Dust Protection Cover
16.8V / 2.3A - Dust Protection Cover
approx. 200 minutes on RP-DC80
–20°C to +45°C (–4°F to +113°F)
Aluminum Alloy
96 × 152 × 59 mm
780 g
