IMPORTANT!
For safety reasons, the concrete ceiling must be capable of supporting
the combined weight of the mount and the displays.
3
Display Size:
37” to 80”
Maximum Load:
2 x 100 lbs
Mounting Pattern:
200 mm x 200 mm to 600 mm x 400 mm
Tilt Range:
up to 15°
Swivel Range:
up to 360°
Profile/Extension:
22.1” to 31.9” (56.1 cm to 81.1 cm)
(A) Lag Bolt (x2)
Washer (x2)
(B) Concrete Anchor (x2)
(C) M5 x 12 Screw (x8)
(D) M5 x 20 Screw (x8)
(E) M6 x 12 Screw (x8)
(F) M6 x 20 Screw (x8)
(G) M6 Washer (x8)
(H) M8 x 12 Screw (x8)
(I) M8 x 20 Screw (x8)
(J) M8 Washer (x8)
(K) Spacer (x8)
(L) M8 Allen Bolt (x2)
(M) M8 Nut (x2)
(N) M6 Cap Nut (x8)
(O) M5X10 Screw (x4)
(P) S5 Allen Key (x1)
(Q) S6 Allen Key (x1)
(R) Wrench (x1)
IMPORTANT!
For safety reasons, this mount must be secured to a wooden ceiling joist. The
joist must be capable of supporting the combined weight of the mount and displays.
1
Set the upper extension pipe aside and drill a 6 mm or 1/4” pilot hole at each marked
location (see Fig. 3).
Attach the upper extension pipe to the ceiling using the lag bolts and washers (A) provided
(see Fig. 4).
Do not release the mount until all bolts are secure.
4
Place the upper extension pipe against the ceiling over the marked joist.
2
5
Part 1A – Mounting to the Ceiling (Drywall)
SPECIFICATIONS
BOX CONTENTS
HARDWARE KIT
INSTALLATION
Read these instructions before you begin.
If you are unsure of any part of the
process, contact a professional contractor or installer for assistance. Improper
installation can result in injury or damage.
The mounting surface must be capable of supporting the combined weight of the
mount and the display; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the ceiling where you wish to install the
mount before drilling.
Safety gear and proper tools must be used. Failure to do so can result in injury or
damage.
Two people are recommended for installation. Do not attempt to lift a heavy display
without assistance.
Follow all instructions and recommendations regarding adequate ventilation and
suitable locations for mounting your display. Consult the owner‘s manual for your
particular display for more information.
CAUTION:
This mount is intended for use only with the maximum weight of 100 lbs per
display (200 lbs total)
. Use with heavier than the maximum weights indicated may result
in instability causing possible injury.
1
2
3
4
5
6
WARNINGS
Upper Extension Pipe (x1)
Lower Extension Pipe (x1)
Cross Bar (x4)
Mount Arm (x4)
Instruction Manual (x1)
Hardware Kit (x1)
Part 1B – Mounting to the Ceiling (Concrete)
Set the upper extension pipe aside and drill a 12 mm or 7/16” hole at each marked location
(see Fig. 6). Remove any excess dust from the holes.
Use a high quality stud finder to locate a ceiling joist where you wish to install your mount
(see Fig. 1). Mark both edges of the joist to help identify the exact center.
NOTE:
Use the center of the joist to avoid cracking or splitting the wood.
3
While another person holds the upper extension pipe in place, mark two locations for
securing the mount to the ceiling (see Fig. 2).
1
2
Place the upper extension pipe against the ceiling in the desired location.
While another person holds the upper extension pipe in place, mark two locations for
securing the mount to the ceiling (see Fig. 5).
Fig.2
RSMCM602
LARGE DUAL CEILING MOUNT
INSTRUCTION MANUAL
INTRODUCTION
Congratulations on your purchase!
We take pride in the quality of our products and are confident you have
received one of the finest mounts on the market. Should you have any
questions or comments, require any assistance, or need replacement parts
for your mount, please contact us by e-mailing [email protected] or calling
1-888-530-7904. You can also visit our website for more information:
www.readysetmount.com.
IF YOU ARE NOT SATISFIED WITH YOUR MOUNT FOR ANY REASON,
PLEASE CONTACT US BEFORE RETURNING IT TO THE RETAILER.
TOOLS REQUIRED
Phillips Head Screw Driver
Ratchet or Driver with 17 mm Socket
Electric or Portable Drill
6 mm or 1/4” Drill Bit and Stud Finder for Drywall Installation
12 mm or 7/16” Masonry Bit for Concrete Installation
Fig. 1
Fig. 3
Fig. 4
Fig. 6
Fig. 5
1/4”
