background image

Raytec Americas: 

+1 613 270 9990 • [email protected]

Raytec Ltd reserve the right to change specifications without prior notification or public announcement.

Version 1

www.raytecled.com

1277-D

-0008

XR Bay luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, 
vibration and rough usage.  The XR Bay luminaire has been certified for use on marine vessels inside, outside, and 
in other severely wet saltwater environments. 

UL 844, UL 1598, UL 1598A, and UL 8750;
CSA C22.2 No. 137, CSA C22.2 No. 250.0 and CSA C22.2 No. 250.13

Hazardous Location Certication:
Class I, Division 2, Groups ABCD;
Class II, Division 2, Groups FG;
Class III; 
Class I, Zone 2, Group IIC;
Zone 22

3 x 3/4” NPT Conduit | Black: Line | White: Neutral | Green: Ground
Optional: Violet: 0-10V Dimming (+) | Grey: 0-10V Dimming (-)
For connections use wire rated to a minimum of 90°C. Class 1 Wiring only.
Dimming control wires must be rated 300V minimum for luminaires with suffix AC,
600V minimum for luminaires with suffix HV.

Certified to:

Connections:

Housing:

Ingress Protection:

Ambient 
Temperature 
Range:

Input Voltage:

Electrical Ratings:

Copper-free Cast Aluminium with Polycarbonate lens

IP66/67 | Suitable For Wet Locations. Marine Outside Type (Salt Water)

Based on luminaire suffix in table below: Suffix - AC: 120-277 VAC | Suffix - HV: 347-480 VAC

Class I Division 2 | Class I Zone 2        Class II Division 2 | Zone 22
XR8: -50°C to +75°C T3C  

        All models -50°C to +50°C T3C

XR10: -50°C to +74°C T3C
XR15: -50°C to +74°C T3C
XR20: -50°C to +67°C T3

Application

Model

Input Voltage

Rated Wattage [Watts]

Rated Voltage 

[Volts]

Freqeuncy

[Hz]

XR8

AC

Flood: 47 Optic: 60

120-277

50/60

HV

Flood: 49 Optic: 64

347-480

50/60

XR10

AC

Flood: 55 Optic: 75

120-277

50/60

HV

Flood: 58 Optic: 77

347-480

50/60

XR15

AC

Flood: 84 Optic: 103

120-277

50/60

HV

Flood: 91 Optic: 107

347-480

50/60

XR20

AC

Flood: 141 Optic: 156

120-277

50/60

HV

Flood: 148 Optic: 160

347-480

50/60

Surface/Ceiling Mounting Installation

SPZ-XR

E477827

Summary of Contents for XR8















Reviews: