background image

INSTALLATION AND OPERATION MANUAL

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, title passes to the

 purchaser upon receipt from the carrier. Consequently, 

claims for the material damaged in shipment must be 

made by the purchaser against the transportation com-

pany at the time shipment is received.

BE SAFE

Your new lift was designed and built with safety in 

mind. However, your overall safety can be increased 

by proper training and thoughtful operation on the part 

of the operator. DO NOT operate or repair this    equip-

ment without reading this manual and the  important 

safety instructions shown inside.

Keep this operation manual near the 

machine at all times. Make sure that 

ALL USERS  read this manual .

6000 POUND CAPACITY
LOW RISE PIT LIFT
   
Models:
P-6
P-6F

1645 Lemonwood Dr.

Santa Paula, CA. 93060,  USA

Toll Free 1-800-253-2363

Tel: 1-805-933-9970

Fax: 1-805-933-9160

www.bendpak.com

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO 

INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT 

YOU FULLY UNDERSTAND AND  COMPREHEND THE FULL CONTENTS OF 

THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO 

OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

REV A 06-13-08

Summary of Contents for BendPak P-6

































Reviews: