background image

Radio control model / Flugmodel

SPACE WALKER

INSTRUCTION MANUAL / Montageanleitung

SPECIFICATION

Wingspan                                  1580mm
Electric Motor                            870 Watt 
Glow Engine              7.5cc 2T / 8.5cc 4T
Radio                     5 Channel / 5 Servos

TECHNISCHE DATEN

Spannweiter                                 1580mm
Elektroantrieb                              870 Watt 
Verbrennerantrieb        7.5cc 2T / 8.5cc 4T
Fernsteuerung              5 Kanal / 5 Servos

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

VQA017 (Single seat)

VQA018 (Two seat)

Summary of Contents for VQA017













Reviews: