Quark-Elec Seatalk QK-A033 Manual Download

Page: 1 / 21

Quark-elec Manual

https://www.quark-elec.com

1 of 21

2019

V1.0

QK-A033

WIFI/USB/NMEA 0183 Multiplexer

Bi-directional routing and filtering

With SeaTalk Converter

Features



Multiplex up to three NMEA 0183 input devices



Configurable baud rates (4800, 9600, 38400bps)



Simultaneous WiFi, USB and NMEA output



Galvanically isolated NMEA and SeaTalk input ports



Differential NMEA output with galvanically isolated protection



Bi-directional USB/WiFi interface enables connection between navigation devices and Autopilot



WiFi – Ad-hoc mode allows up to 4 devices to connect to the internal WiFi module simultaneously



WiFi – Station mode allows for the connection of the A033 to your router/ access point for greater

number of wireless users and WiFi range.



SeaTalk to NMEA 0183 protocol converter



Wide range of power supply voltage tolerance (DC 9-35 Volts)



Compatible with Windows, Mac, Linux,



Compatible with Android and iOS excluding Configuration and USB functions. (Please note

Configuration must be completed using Windows software.)



Advanced filtering and routing functions allows for full overflow reduction and additional

configuration of the multiplexer.



Monitoring of NMEA data passing through the device.

Summary of Contents for Seatalk QK-A033






















Search results

Summary of Contents for Seatalk QK-A033

Reviews:

Related manuals for Seatalk QK-A033

Brands by name

Popular brands

Quark-Elec Seatalk QK-A033, Manual

Search results

Summary of Contents for Seatalk QK-A033

Reviews:

Related manuals for Seatalk QK-A033

Brands by name

Popular brands