Quadra-Fire TOPAZ-MBK-IPI Скачать руководство пользователя

Страница: 1 / 62

Quadra-Fire • TOPAZ-MBK-IPI, TOPAZ-D-PMH-IPI, TOPAZ-D-MBK-IPI, TOPAZ-D-CSB-IPI Installation Manual • 2341-980_R10 • 11/15

Installation Manual

Installation and Appliance Setup

INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.

NOTICE: DO NOT

discard this manual!

This appliance may be installed as an OEM installation

in manufactured home (USA only) or mobile home and

must be installed in accordance with the manufacturer’s

instructions and the manufactured home construction

and safety standard,

Title 24 CFR, Part 3280

Standard

for Installation in Mobile Homes, CAN/CSA Z240MH, in

Canada.
This appliance is only for use with the type(s) of gas

indicated on the rating plate.

Models:

TOPAZ-MBK-IPI

TOPAZD-PMH-IPI

TOPAZD-MBK-IPI

TOPAZD-CSB-IPI

In the Commonwealth of Massachusetts installation must be

performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth

of Massachusetts requirements.

DO NOT

store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

- What to do if you smell gas

•

DO NOT

try to light any appliance.

•

DO NOT

touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

- Installation and service must be performed by a qualified

installer, service agency, or the gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a fire or

explosion may result causing property damage,

personal injury, or death.

HOT GLASS WILL CAUSE

BURNS.
DO NOT TOUCH GLASS

UNTIL COOLED.
NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns

from the hot viewing glass is provided with

this appliance and shall be installed for the

protection of the children and other at-risk

individuals.

DANGER

Cabinet Style

Solitaire

Содержание TOPAZ-MBK-IPI































































Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды

Quadra-Fire TOPAZ-MBK-IPI, Руководство по установке

Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды