![background image](http://html1.mh-extra.com/html/qazqa/new-york-wl-dark-grey/new-york-wl-dark-grey_instruction-manual_4364886001.webp)
100°
Fig.1(A) Detection Range
2M
2.0 M
8M
5M
F ig.1(B )
O K
Fig.1(C ) N O T G O O D
Fig. 1(D)
Wall
Roo
f
North
New York WL Dark Grey
92303
INSTRUCTION MANUAL
Unchangeable LED
Max.4x0.5W LED
3000K±300K
10000H
3 x 1.2V AA
900mAh
Ni-MH
Rechargeable
battery
III
IP44
INTRODUCTION
The L antern Light has a build-in PIR
(Passive Infra Red) sensing device which
continuously scans a preset zone and
automatically switches the light on when it
detects movement in that area. Once
movement is detected within the range of
the sensor the light will switch on
automatically to illuminate pathways,
steps, patios, porches, or whatever area
you have selected to light for reasons of
safety, convenience or security. While
there is movement within range of the unit
the light will remain on.
During the day, the solar panel converts
sunlight into electricity to recharge the
batteries for LED light. This Lantern Light
has an adjustable TIME dial that allows
light duration of up to 90 seconds. When
the batteries are fully charged, it is
estimated that LED can work up to max. 60
times when TIME be set to 1.5 minutes,
totally 1.5 hours.
This unit includes 3 x 1.2V AA 900mAh
Ni-MH Rechargeable battery batteries,
which need to be replaced after 2-years
use, because the charging ability will
decrease.
HAVE YOUR SENSOR WORKED
WELL
To have sensor worked well, we suggest
you take the following points into account:
►
►
►
■
Ideally the Lantern Light should be mounted
1.8 to 2.5 meters (6 to 8ft) above the area to be
scanned (refer to Fig.1A).
■
To avoid damage to unit, do not aim the sensor
towards the sun.
■
To avoid nuisance triggering, the sensor should
be directed away from heat sources such as
barbecues, Air-conditioners, other outside lighting,
moving cars and flue vents.
■
To avoid nuisance triggering, keeping away from
the area of strong electromagnetic disturbance.
■
Do not aim towards reflective surfaces such as
smooth white walls, swimming pools, etc...
■
The sensor scanning specifications (approx. 6
meters at 100°-- round) may vary slightly depending
on the mounting height and location. The detection
range of the unit may also alter with temperature
change. Before selecting a place to install your lantern
light you should note that movement across the scan
area is more effective than movement directly toward
or away from the sensor (refer Fig.1B). If movement is
made walking directly towards or away from the
sensor and not across, the apparent detection range
will be substantially reduced. (refer to Fig. 1C)
CHOOSE LOCATION FOR YOUR LIGHT
■
This light’s power comes
from sunlight. For max sun
exposure and longer light
output, place the solar
panel, connecting to the
light, in a position that
receives at least 4-6 hours
direct sunlight per day.
(
refer to Fig. 1D
)
Ideally,
the solar panel should be
adjusted to the angle facing
the sun. Placing the solar
panel in a shaded location
will not allow the batteries to be charged fully. It will
reduce the number of hours the light operates per
night.
■
This Solar Light is ideal for areas where electricity
is not available, including driveways, garages,
entrance doors, backyard sheds and other remote
areas, for safety and convenience around your home.
222.2 mm
177.1mm
374.4
mm
161.1
mm
127mm
120.3 mm
Fig.2(A)