1
SET UP INSTRUCTIONS
3784 – 79” THREE TIER BOCA HEXAGON FOUNTAIN ON 6’ POOL
3786 – 78” THREE TIER BOCA ROUND FOUNTAIN ON 6’ POOL
Open bag containing the pump kit
P51504
. In the kit you will find:
1 - 02617 (515 gallons per hour pump)
1 – 3/4" X 1/2" plastic tee
1 – rubber stopper
1 - 3/4" clear tubing 75” long
1 – 1/2" plastic ell
1 - tube of silicone
1 - 1/2" kink free tubing 6” long
1 – putty tape 12” long
1 – hose clamp
1. Prepare a level base of 4” poured concrete or 6” compacted crushed limestone. The completed 6’ fountain pool has an outside base
diameter of 77”.
2. In the center of the 6’ fountain pool you will see a PVC insert. Find the pump and run the plug end of the power cord down the PVC
insert. Leave two feet of slack on the power cord from the pump to the PVC insert. Find the tube of silicone and the rubber stopper. Fill
the hole in the rubber stopper with silicone. Slip the rubber stopper onto the power cord with the smaller end facing away from the
pump. Apply silicone around the outside edge of the rubber stopper. Insert the rubber stopper snugly into the PVC insert. Apply more
silicone on top and around the top edge of the rubber stopper. Don’t skimp on the silicone you want a water tight seal.
3. Place the 6’ fountain pool in the center of the area where the fountain is to be displayed. Retrieve the power cord from bottom side
of pool and place the power cord in the groove in the bottom of pool.
4. Find the pump house and carefully position it in the center of the pool. The opening in the pump house should face toward back of
fountain. Find the pedestal and carefully position it on top of the pump house. Find the larger shell and position it on top of the
pedestal and level in all directions. Shim as needed.
5. Find the piece of 3/4" clear tubing 75” long and the hose clamp. Run one end of the 3/4" clear tubing down the hole that is in the
center of the shell and down through the hole in the center of the pedestal into the pump house. Connect the 3/4" clear tubing to the
outlet of the pump with the hose clamp. Position the pump in the pump house and make sure that the pump is seated on the floor of
the pool.
6. Find the spacer and run the 3/4" clear tubing up thru the hole in the center of the spacer. Position the spacer on top of the larger
shell and level in all directions. Find the second shell and run the 3/4" clear tubing up thru the hole in the center housing of the shell.
Position the shell on top of the spacer and level in all directions. Make sure that the pump is seated on the floor of the pool.
Cut the 3/4" clear tubing 1” below the top surface of the center housing in the second shell.
7. Find the 3/4" X 1/2" plastic tee, the 1/2" plastic ell and the 1/2" kink free tubing. Attach one end of the 1/2" kink free tubing onto the
middle connection on the 3/4" X 1/2" plastic tee. Attach the 1/2" plastic ell onto the opposite end of the 1/2" kink free tubing. Attach an
end connection on 3/4" X 1/2" plastic tee onto the end 3/4” clear tubing located in the center of the second shell. Attach the remainder
of the 3/4" clear tubing onto the opposite end connection of the 3/4" X 1/2" plastic tee.
8. Find the third shell and run the 3/4" clear tubing up thru the hole in the center housing of the shell. Place the 1/2" kink free tubing in
the groove located in the bottom of the third shell with the elbow on the outside of the center housing pointing down.
Position the shell on top of the second shell and level in all directions. Check to make sure that the pump is seated on the floor of the
pool inside the pump house. Cut the 3/4" clear tubing 6” above the top surface of the center housing on the third shell.
9. Find the putty tape, remove the backing. Wrap the putty tape around the 3/4" clear tubing on its self just above PVC pipe in the top
shell. Push the putty tape down into the PVC pipe all around the 3/4" clear tubing.
You want to create watertight seal so use all of
the putty tape.
Find the finial. Slip the finial onto the 3/4" clear tubing and position the finial on top of fountain.
10. Find the drain plugs and insert snugly into the drain inserts located in the pool and the two larger shells of the fountain. Remove
any tape and or dirt from the drain insert before you insert the drain plug.
11. Find the four pool wall sections. Position each piece of the wall section around the fiberglass pool, lining up the inside radius of the
wall section with the inside radius of the fiberglass pool.
