background image

Device

 

Diagram

Please

 

follow

 

the

 

following

 

installation

 

step

Please

 

check

 

the

 

following

 

items

 

before

 

installation

if

 

any

 

missing

please

 

contact

 

your

 

dealer

.

     Power

 

Supply

 

Unit                                                         

                 

1pc

     

Power

 

Receiving

 

Unit

                                                                 

1pc

     

User

 

Manual

                                                                                

1pc 

  

1 Turn off the signal and display device install the product with power on may damage the

 

     transmission device;
2) Check the power consumption

 

of

 

network terminal, current

 

and

 

power

 

voltage

;

    if it is 12V device, please select 15V power supply; refer to the power supply table, confirm if the  
    voltage meet the requirement after transmission;

    if it is 24V device, please select 24V

 

power supply

;

 refer to the power supply table, confirm if the 

    voltage meet the requirement after transmission;
    if it is PoE power supply, please select 48V 0.5A power supply,

 

and make sure the ethernet 

    transmission distance is in 100 meters;
3) Connect power supply unit’s RJ45

 

with switch, and DC connector with power supply, then the

 

 

   network cable connect with the RJ45-F;

4) In terminal device, connect the power receiving unit’s RJ45

-

M with network port, and DC power

 

 

   connector with power, network cable connect with the RJ45-F;

5) Network terminal work normally.

   

 

 

 

 

 

 

   

 

 

Installation

 

Step

This

 

ethernet

 

power

 

supplies

 

include

 

a

 

power

 

supply

 

unit

 

and

 

a

 

power

 

receiving

 

unit

it

 

uses

 

in

 

10

/

100M

 

network

it

 

transfers

 

the

 

power

 

for

 

the

 

remote

 

device

 

over

 

Cat5

/

5e

/

6

 

cable

This

 

product

 

use

 

4

,

5

,

7

,

8

 

pin

 

to

 

transfer

 

power

the

 

distance

 

can

 

up

 

to

 

50

 

meters

At

 

the

 

same

 

time

 ,

the

 

output

 

voltage

 

is

 

15V

,

24V

,

48V

 

optional

Besides

work

 

with

 

4ch

 

or

 

8ch

 

power

 

  distribution  wire.  The

 

product

 

can

 

make

 

various

 

combination

 

to

 

save

 

the

 

cost

 

and

 

wiring

 .

The

 

product

 

is

 

widely

 

used

 

in

 

security

 

surveillance

 

monitor

 

and

  

network

 

engineering

It

'

s

 

easy

 

application

 

and

  

stable

 

function, 

this product is widely used in security surveillance monitor and network engineering sites.

1

Please use standard Cat5e/6

 

cable

 

to

 

guarantee

 

the

 

power

 

and

 

ethernet

 

transmission

 

distance

!

2

The

 

product

 

is

 

passive

without

 

stable

 

voltage

current

 

limit

 

and

 

control

 

power

 

circuit

Please

 

select

 

 

   the

 

power

 

according

 

to

 

the

 

terminal

 

device

 

consumption

,(

refer

 

to

 

the

 

voltage

 

table

), 

and

  

avoid

 

to

 

 

    damage

 

the

 

device

!

Note

1

2

Injector

 

Diagarm

 

Splitter

 

Diagram

R  45-F

R  45-

F

R  45-

M

R  45-

M

Power

-

F

Power

-

M

J

J

J

J

   

Pin

         

Signal

                    

1                Data

2                Data
3                Data
4                

+

Power

5                

+

Power

6                Data
7                

-

Power

8                

-

Power

Mid-Span

Cat5/5e/6

Power Supply Unit 

Power Receiving Unit 

 Power15V

IP

 

Camera

Network Switch

Power Input

Ethernet

Application 1 Single Channel Power Supply

 

 

 

 

Network Switch

P

ower  Input

Ethernet

DC15V

+

-

Power

 

Distributrion Wire

Power

 

Input

IP

 

Camera

Power receiving Unit

Power Supply Unit

Cat5/5e/6

Application 2 Multi Channel Powr Supply

 

 

 

 

Apply in 10

/

100M

 

network

 provide power for the terminal device in 0

--

50 distance;

Adopt

 

Mid

-

Span

:

1,2

,

3, 6

 

pin

 

to

 

transfer

 

ethernet

4,5,7

,

8

 

pin to transfer power;

According

 

to

 

the

 

terminal

 

device

 

consumption

it

 

can

 

select

 

15V

,

24V

,

48V

at

 

the

 

same

 

time

 

is

related

 

with

 

the

 

distance

;

Multi

 

power

 

supply

 

can

 

use

 

at

 

the

 

same

 

time

 

via

 

power

 

distribution

 

wire;

Provide

 

power

 

for

 

IP

 

camera

wireless

 

AP

IP

 

telephone.

Feature

DCoE-01
DC over Ethernet

DCoE-01 DC over Ethernet

Reviews: