1-66-729A
Automatic Lockset Key/Turn (
Unified)
M5 Bolt
from the
other side
of the door
70
1“ Screws
1” Screws
90
70
1” Screws
PR4-58E
Euro Profile Escutcheon
PR4-729A
Anti-ligature Pull Handle
3
32
25
90
205
175
14
11
25
32
58
10
48.50
25°
PR6134-AL NL-(NHB)
Dead locking
Nightlactch
PR6133-AL NL-(HB)
with Holdback
(Non-Holdback Standard)
PR6136-AL NL-(NHB)
Dead locking
Nightlactch
PR6133-AL NL-(HB) with Holdback
(Non-Holdback Standard)
PR4-58E
Euro Profile
Escutcheon
PR4-729A
Anti-ligature
Pull Handle
PR7101-TPSP
Thumb Turn
Support Plate
Description
Auto Locking Night Latch
Spindle Universal 44mm-63mm with O-ring
Turn/Pull complete
729 Pull Handle
Escutcheon 58mm Euro
729, 90 x 205mm Radius plate
3x25x79mm Thumb turn support plate
Fixings Included
Note:
The cylinder cut out is made on the external side of the door only and must not go right through the door.
Model
Spindle Length Calculation
46
Door Thickness ÷ 2 + 20mm
+3mm
56
Door Thi 11mm
+3mm
66
Door Thickness ÷ 2 + 20mm
+3mm
76
N/A
N/A
86
N/A
N/A
96
N/A
N/A
Note A :
Check exact door thickness of each door
Note B :
Turn/Pull support plate must not be recessed
deeper than the surface of the door.
PR1 Variant
Addition for
Turn/Pull
Repair Plate
46
Door Thickness Less 3mm
56
Door Thickness Less 3mm
66
Door Thickness Less 3mm
76
N/A
86
N/A
96
N/A
If Fitting
Turn/Pull
Repair Plate
Screw Length
= Door
Thickness
Turn/Pull Screw Length
Note: If, when fitting the pull handle, the screws make direct contact with the lockcase, please use the shorter (5/8“)
screws included in the fixing pack.
Standard Primera Products are designed for internal applications only. For external applications products plated to
“Service Condition 5” should be used.
To change the handing of the latch, firstly
remove the retaining screw, insert a flat
bladed screwdriver behind the latch to
ease it out, rotate the latch 180° and
reposition in the lockcase securing
screw from the opposite side.
103
72
133.5
22
31
59.5
235
165
80
3
11
70
10
Note:
Unless ordered seperatley the cylinder
is not included in this kit.
A: This Turn/Pull is equipped with a screw to adjust the projection of the
spindle if required (most likely if the spindle is cut too short in error) see
drawing A
B: When cutting the spindle to the required length, please make sure that
the material is cut from the end marked B as illustrated. The 3 slots at
the opposite end of the spindle C are an important safety feature and
designed to sheer at 50NM to protect the lock and ensure clinical staff
maintain control of the lock at all times. The O-ring in the first slot will
also assist in the retention of the spindle in the nozzle of the Turn/Pull
during normal use.
There must be at least I sheer
point between the end of the
Turn/Pull nozzle & the lockcase.
Important Spindle & Turn/Pull Information
Sheer Points
Do Not Cut Here
O-Ring
Lockcase
Lockcase
Door
A
B
C
Adjust the spindle projection screw
by inserting screwdriver through
the door/lockcase.
The spindle must
engage in the socket
by at least 7mm
Adjust length of spindle by cutting with a
hacksaw at this end. It is important that
the end of the spindle is cut square.
SOP105 Revision (2)
Primer
a Limited, Unit 8 Bankfield House, 250 Bristol
Av
enue, Blackpool, FY2 0JF
t
0330 058 0988
e
w
www
.safehingeprimera.com
Important Note: products are protected by Intellectual Property Rights including UK and Community Unregistered Design Rights, UK and Community Registered Designs and UK Patents and Patent Applications.
For further details please contact Safehinge Primera Limited.
Note: Please ensure this
screw is secured tighly.
