5. Attach ONE DEVICE
to the timer
Plug the device into the outlet
on the side of the timer.
Heavy Duty
24-Hour Timer
Model: TNINL2412
HELPFUL TIPS
• This timer repeats the same settings daily.
• To push down or pull up the gray pins, use your
finger or the tip of a small non-metalic insulated
tool, such as a pencil or toothpick.
• Set up to 48 different “ON” and “OFF” times in a 24
hour period by the positioning of the gray pins. Pins
pressed down represent the ‘ON’ time. Pins in the
up position represent ‘OFF’ time.
• Switching the timer to “OUTLET ON” will bypass
programming, however, the timer dial will continue
to rotate and maintain the current time.
• Once the timer is plugged into an outlet, it will sit at
a slight upward angle making it easier to read and
program the unit.
IN CASE OF POWER FAILURE
Timer will stop operating if the power goes out.
Once power is restored, reset the time of day as
explained in Step 2 of the instructions.
LIMITED 1 YEAR WARRANTY
Prime warrants this product to be free from manufacturing defects
for a period of one year from the original date of purchase
(“warranty period”). This warranty is limited to the repair or
replacement of this product only and Prime is not liable for any
consequential or incidental damage to other products that may be
used with this unit. This warranty is effective only if such unit is
returned to Prime not later than thirty (30) days after the expiration
of the warranty period. Warranty is void if damage is due to neglect,
misuse, alteration, modification, improper installation, or repair by
other than Prime. This warranty is in lieu of all other warranties
express or implied. Some states do not allow limitations on how
long an implied warranty lasts or permit the exclusion or limitation
of incidental or consequential damages, so the above limitations
may not apply to you.
It is our experience that a product that fails prematurely due to a
manufacturing defect in materials or workmanship, will generally do
so very early in the product’s life cycle, often the first or second time
the product is used. Products that are returned for warranty
inspection after months or years of continuous reliable service are
usually the result of normal wear and tear, which is not considered
a defect in materials or workmanship and therefore is not covered
by the warranty.
This warranty gives you specific rights, and you may also have
other rights which vary from state to state. If unit should prove
defective within the warranty period, return within the time period
set forth above prepaid with the original purchase receipt to:
Prime Wire & Cable, Inc.
ATTN:
Timer
Warranty
280 Machlin Court
City of Industry, CA 91789
Service - (888) 445-9955 • www.primewirecable.com
NIGHTLIGHT INCLUDED!
Light-sensing photocell
automatically turns nightlight ON
and OFF when the environment
becomes dark or light.
SAFETY INFORMATION & SPECIFICATIONS
THIS TIMER IS A “GROUNDED” DEVICE
The male plug contains a ground pin and is
only intended for use with a three-pronged
grounded outlet.
THIS TIMER IS FOR USE WITH A 125VAC POWER SOURCE.
125VAC / 60Hz
DO NOT ATTACH A DEVICE THAT EXCEEDS THE UNIT RATINGS:
15A / 1875W Resistive
(General Purpose)
10A / 1250W Tungsten
(Incandescent)
1/2 HP
(Horsepower Motor)
1. Set a period of time for
the timer to be “ON”
Make sure all pins are in the UP
position before beginning. Locate
the gray pins and push them DOWN
at the marked times when the
attached device is to be “ON”. Each
pin represents a 30 minute time
interval. Example: “ON” time is
7:00pm, “OFF” time is 11:00pm.
Push down all of the pins between
the 7:00pm arrow and the 11:00pm
arrow.
2. Set the “CURRENT TIME”
Rotate the entire gray push-pin
dial clockwise until the arrow
marked “CURRENT TIME” aligns
with the current time of day on the
dial. “AM” hours are highlighted in
WHITE. “PM” hours are
highlighted in BLACK.
3. Set “BYPASS SWITCH”
When the switch is in the “TIMER
ON” position, timer will automatically
turn the attached device on and off.
When the switchis in the “OUTLET
ON” position, timer will bypass the
programming and the attached
device will remain on.
4. Plug timer into an
ELECTRICAL OUTLET
Timer will rest against outlet at
a slight upward angle, making it
easier to see and operate the
push-pin dial.
STEP-BY-STEP
INSTRUCTIONS
WARNING
Risk of Electric Shock
Keep children away. Unplug timer before cleaning. Fully
insert plug. Do not use in wet locations.
Risk of Fire
Do not use to control appliances that contain heating
elements (cooking appliances, heaters, irons, etc.). Do not
exceed electrical ratings. For Indoor Use Only.
AVERTISSEMENT
Risque de choc électrique
Garder hors de portée des enfants. Débrancher la
minuterie avant de nettoyer. Insérer complètement la fiche.
Ne pas utiliser dans les endroits mouillés.
Risque d’incendie
Ne pas utiliser pour contrôler les appareils contenant des
éléments chauffants (équipements de cuisine, radiateurs,
fers à repasser, etc.). Ne pas excéder la capacité
électrique. Pour usage à l’intérieur seulement.
