background image

1.  Set a period of time for  

 

  the timer to be “ON”

  Make sure all pins are in the UP    

  position before beginning. Locate   

  the gray pins and push them DOWN  

  at the marked times when the  

 

  attached device is to be “ON”. Each  

  pin represents a 30 minute time    

  interval. Example:  “ON” time is    

  7:00pm, “OFF” time is 11:00pm.    

  Push down all of the pins between    

  the 7:00pm arrow and the 11:00pm   

 arrow. 

2. Set the “CURRENT TIME”

  Rotate the entire gray push-pin    

  dial clockwise until the arrow  

 

  marked “CURRENT TIME” aligns   

  with the current time of day on the  

  dial. “AM” hours are highlighted in   

  WHITE. “PM” hours are   

 

  highlighted in BLACK. 

3.  Set “BYPASS SWITCH”

  When the switch is in the “TIMER   

  ON” position, timer will automatically  

  turn the attached device on and off.   

  When the switchis in the “OUTLET    

  ON” position, timer will bypass the    

  programming and the attached  

 

  device will remain on.

 

4. Plug timer into an    

 

  ELECTRICAL OUTLET

  Timer will rest against outlet at    

  a slight upward angle, making it   

  easier to see and operate the    

  push-pin dial.

HELPFUL TIPS

•  This timer repeats the same settings daily.

•  To push down or pull up the gray pins, use your  

  finger or the tip of a small non-metalic insulated  

  tool, such as a pencil or toothpick.

•  Set up to 48 different “ON” and “OFF” times in a  

  24 hour period by the positioning of the gray pins.  

  Pins pressed down represent the ‘ON’ time. Pins  

  in the up position represent ‘OFF’ time. 

•  Switching the timer to “OUTLET ON” will bypass  

  programming, however, the timer dial will  

 

  continue to rotate and maintain the current time.

•  Once the timer is plugged into an outlet, it will   

  sit at a slight upward angle making it easier to   

  read and program the unit.

IN CASE OF POWER FAILURE

Timer will stop operating if the power goes out. 

Once power is restored, reset the time of day as 

explained in Step 2 of the instructions.

SAFETY INFORMATION & 

SPECIFICATIONS

THIS TIMER IS A “POLARIZED” DEVICE
One blade on the male plug is wider than   

 

the other and is only intended for use with   

 

a polarized outlet. Use with a three-pronged  

 

grounded outlet is also acceptable.

THIS TIMER IS FOR USE WITH A 125VAC POWER 

SOURCE.

125VAC / 60Hz

DO NOT ATTACH A DEVICE THAT EXCEEDS THE 

UNIT RATINGS:

15A / 1875W Resistive

 (General Purpose)

10A / 1250W Tungsten

 (Incandescent)

1/2 HP 

(Horsepower Motor)

LIMITED 1 YEAR WARRANTY

Prime warrants this product to be free from manufacturing defects 

for a period of one year from the original date of purchase 

(“warranty period”). This warranty is limited to the repair or 

replacement of this product only and Prime is not liable for any 

consequential or incidental damage to other products that may be 

used with this unit.  This warranty is effective only if such unit is 

returned to Prime not later than thirty (30) days after the expiration 

of the warranty period. Warranty is void if damage is due to neglect, 

misuse, alteration, modification, improper installation, or repair by 

other than Prime. This warranty is in lieu of all other warranties 

express or implied. Some states do not allow limitations on how 

long an implied warranty lasts or permit the exclusion or limitation 

of incidental or consequential damages, so the above limitations 

may not apply to you. 
It is our experience that a product that fails prematurely due to a 

manufacturing defect in materials or workmanship, will generally do 

so very early in the product’s life cycle, often the first or second time 

the product is used. Products that are returned for warranty 

inspection after months or years of continuous reliable service are 

usually the result of normal wear and tear, which is not considered 

a defect in materials or workmanship and therefore is not covered 

by the warranty.
This warranty gives you specific rights, and you may also have 

other rights which vary from state to state. If unit should prove 

defective within the warranty period, return within the time period 

set forth above prepaid with the original purchase receipt to:
Prime Wire & Cable, Inc.   

 

 

 

ATTN: 

Timer 

Warranty 

 

    

280 Machlin Court 

 

 

 

 

City of Industry, CA 91789  

 

 

 

Service - (888) 445-9955  •  www.primewirecable.com

24-Hour 

Timer

Model: TNI2412

STEP-BY-STEP 

INSTRUCTIONS

                           WARNING

Risk of Electric Shock

Keep children away. Unplug timer before cleaning. Fully 

insert plug. Do not use in wet locations.

Risk of Fire

Do not use to control appliances that contain heating 

elements (cooking appliances, heaters, irons, etc.). Do not 

exceed electrical ratings. For Indoor Use Only.

                           AVERTISSEMENT

Risque de choc électrique

Garder hors de portée des enfants. Débrancher la 

minuterie avant de nettoyer. Insérer complètement la fiche. 

Ne pas utiliser dans les endroits mouillés.

Risque d’incendie

Ne pas utiliser pour contrôler les appareils contenant des 

éléments chauffants (équipements de cuisine, radiateurs, 

fers à repasser, etc.). Ne pas excéder la capacité 

électrique. Pour usage à l’intérieur seulement.

5.  Attach ONE DEVICE to the    

 timer

  Plug the device into the outlet    

  on the side of the timer. Make    

  sure the attached device is    

  switched ON.

Outlet

ON

Timer

ON

Reviews: