background image

 

Part 1 

 
 
 
 

FCC Notes: 

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions manual, may cause interference to radio 
communications. It has been tested and found to comply with limits for a Class A digital device 
pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable 
protection against interference when operated in a commercial environment. Operation of this 
equipment in a residential area is likely to cause interference in which case the user at his own 
expense will be required to take whatever measures to correct the interference. 
 

Warranty Limits: 

Warranty terminates automatically when any person other than the authorized technicians opens 
the machine. The user should consult his/her dealer for the problem happened. Warranty voids if 
the user does not follow the instructions in application of this merchandise. The manufacturer is 
by no means responsible for any damage or hazard caused by improper application. 
 

About This Manual: 

Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex 
will assume no liability for any

 

technical inaccuracies or editorial or other errors or omissions 

contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, 
including without limitation loss of data or profits, resulting from the furnishing, performance, or 
use of this material. 

 

This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims any 
warranties, expressed, implied or statutory, including without limitation implied warranties of 
merchantability or fitness for particular purpose, good title and against infringement. 
The information in this manual contains only essential hardware concerns for general user and is 
subject to change without notice. Posiflex reserves the right to alter product designs, layouts or 
drivers without notification. The system integrator shall provide applicative notices and 
arrangement for special options utilizing this product. The user may find the most up to date 
information of the hardware from web sites: 

www.posiflex.com

/www.posiflex.com.tw

 or 

/www.posiflexusa.com. 
 
All data should be backed-up prior to the installation of any drive unit or storage peripheral. 
Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of 
this or any other Posiflex product. 
 
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a 
retrieval system, or transmitted in any form or by any means, electronic, mechanical, 
photocopying, or otherwise, without prior express written consent from Posiflex Technology, Inc. 
the publisher of this documentation. 

 

©

 Copyright Posiflex Technology, Inc. 2010

 

All  brand  and  product  names  and  trademarks  are  the  property  of  their 
respective holders.

 

Jiva/TP/LT – 8300/E  

Touch Terminal 

User’s Manual

 

Rev.: B0 

P/N: 16340900030 

警告使用者

警告使用者

警告使用者

警告使用者

 

這是甲類的資訊產品,在居住的環
境 中使 用 時 , 可 能會 造 成 射 頻干
擾,在這種情況下,使用者會被要

求採取某些適當的對策。

 

T31454 

Summary of Contents for Jiva - E




















Reviews: