Page 1 of 3
Posh Solus Mk3 Rail Shower 1 Function Chrome (4*)
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Installation Instructions
Step 2
Insert the rail, slider and soap dish.
into place.
Fix the rail in place using the rubber
bush and brass nut on both pillars.
Replace chrome pillar caps.
•
•
•
Step 3
To adjust slider position, push button to
unlock and and release button to lock
the slider.
•
1850mm (Recommended)
680mm Rail
580mm
Chrome Cap
FLOOR
Step 1
Remove chrome caps from each pillar.
Mount the top and bottom pillars in desired
position with the screws and wall plugs.
Check the mounts are vertically aligned.
•
Rail
Slider
Elbow
(if supplied)
Brass Nut
*This product must be installed in
compliance with all relevant regional
regulations.
It is the responsibility of the installer to
ensure a waterproof seal is achieved
between the product and mounting
surface. If in doubt about the quality of
the seal, remove the product and
reinstall using silicone to ensure a seal is
achieved.
All pipe work must be thoroughly flushed
prior to the installation of the hose.
After installation all connections must be
checked for leaks.
All outlets used primarily for personal
hygiene shall deliver water at a safe
temperature as per regional regulations.
•
•
•
•
IMPORTANT:
Please read all of the
instructions before installation.
General:
•
Wall Plug
(Recommended)
Chrome Cap
Rubber Bush
Screw
Slider button
Important Installation Considerations
1. NOTE: Some showers may not provide an effective shower when used
with gravity fed heated water systems or where pressures are less
than 150kPa at the outlet. Additionally showers with flow rates of less
than 9L/min may not allow the following to function correctly:
_ some instantaneous water heaters
_ some tempering valves
_ some thermostatic mixing valves
2. Some shower heads only operate correctly when hot and cold water
supplies are both mains pressure and may not be suitable for some
instantaneous hot water services.
3. When water pressure is in excess of 500kPa a pressure limiting device
is required in accordance with AS/NZS 3500 1.12 recommendation
www.methven.com
Methven warrants this product against manufacturing defects and that it is suitable for use
under the general operating conditions specified in this instruction sheet. However, regional
regulations apply and may affect your warranty. Please refer to
customer service for full details.
New Zealand
0800 804 222
Australia
1300 638 483
UK
0800 195 1602
98-0284
ISSUE A
DECEMBER 2015
Technical Specifications:
Operating Pressure:
Min: 150kPa/1.5bar
Max: 500kPa/5.0bar*
Optimum: 150kPa/1.5bar - 500kPa/5bar
Operating Temperature:
Hot: Max 80°C*
Cold: Min 5°C
Inlet Connections:
All ½" BSP
* Regional specific regulations apply.
Please refer to your warranty statement at
www.methven.com
TWIN SHOWER SYSTEM
Installation Guide
Recommended installation of pressure limiting
valve if supply exceeds 500kPa
NOTE:
- After installation all connections must be
checked for leaks
- All installations must be carried out in
compliance with relevant water regulations*.
Important Installation Considerations
1. NOTE: Some showers may not provide an effective shower when used
with gravity fed heated water systems or where pressures are less
than 150kPa at the outlet. Additionally showers with flow rates of less
than 9L/min may not allow the following to function correctly:
_ some instantaneous water heaters
_ some tempering valves
_ some thermostatic mixing valves
2. Some shower heads only operate correctly when hot and cold water
supplies are both mains pressure and may not be suitable for some
instantaneous hot water services.
3. When water pressure is in excess of 500kPa a pressure limiting device
is required in accordance with AS/NZS 3500 1.12 recommendation
www.methven.com
Methven warrants this product against manufacturing defects and that it is suitable for use
under the general operating conditions specified in this instruction sheet. However, regional
regulations apply and may affect your warranty. Please refer to
customer service for full details.
New Zealand
0800 804 222
Australia
1300 638 483
UK
0800 195 1602
98-0284
ISSUE A
DECEMBER 2015
Technical Specifications:
Operating Pressure:
Min: 150kPa/1.5bar
Max: 500kPa/5.0bar*
Optimum: 150kPa/1.5bar - 500kPa/5bar
Operating Temperature:
Hot: Max 80°C*
Cold: Min 5°C
Inlet Connections:
All ½" BSP
* Regional specific regulations apply.
Please refer to your warranty statement at
www.methven.com
TWIN SHOWER SYSTEM
Installation Guide
Recommended installation of pressure limiting
valve if supply exceeds 500kPa
NOTE:
- After installation all connections must be
checked for leaks
- All installations must be carried out in
compliance with relevant water regulations*.
97-2821
Apr-2018
