background image

Installation

ENGLISH

Note:

Check all connections and systems before final
installation.

Do not use unauthorized parts. The use of 
unauthorized parts may cause malfunctions.

Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.

Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result

of a sudden stop.

The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.

Optimum performance is obtained when the unit
is installed at an angle of less than 60°.

DIN Front/Rear-mount

This unit can be properly installed either from
“Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.

DIN Front-mount

Installation with the rubber bush 

1. Insert the mounting sleeve into the dashboard.

When installing in a shallow space, use a sup-
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.

2. Secure the mounting sleeve by using a screwdriv-

er to bend the metal tabs (90°) into place.

3. Install the unit as illustrated.

Removing the Unit

1. Extend top and bottom of the trim ring outwards

to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)

It becomes easy to remove the trim ring if the
front panel is released.

2. Insert the supplied extraction keys into both sides

of the unit until they click into place.

3. Pull the unit out of the dashboard.

53

53

1

1

182

182

60

°

Trim ring

Dashboard

Mounting sleeve

Rubber bush

Screw

DIN Rear-mount

1. Extend top and bottom of the trim ring outwards

to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)

It becomes easy to remove the trim ring if the
front panel is released.

2. Determine the appropriate position where the

holes on the bracket and the side of the unit
match.

3. Tighten two screws on each side.

Use either truss screws (5 mm 

×

8 mm) or

flush surface screws (5 mm 

×

9 mm), depend-

ing on the shape of screw holes in the 
bracket.

Fastening the front panel

If you do not plan to detach the front panel, the
front panel can be fastened with supplied screw.

Trim ring

Screw

Dashboard or Console

Factory radio mounting bracket

Screw

Note:

When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key.
Otherwise, battery drain may result.

Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a
battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.
— Never cut the insulation of the power cable of

this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.

— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s nega-

tive cables.

Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.

Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.

IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.

Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
they are accidentally detached.

Cord function may differ according to the
product, even if cord color is the same. When
connecting this system, be sure to check all
manuals and connect cords correctly.

No ACC position

ACC position

ON

S

T

A

R

T

O

FF

ACC

ON

S

T

A

R

T

O

FF

<KSNNX> <06K00000>

DEH-P690UB

Printed in Thailand
Imprimé en Thaïlande

<CRD4161-A/N> UC

Connecting the Units

ENGLISH

This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.

INST

ALLA

TION MANUAL

MANUEL D’INST

ALLA

TION

Summary of Contents for DEH-P690UB - Premier Radio / CD

Page 1: ...ole Factory radio mounting bracket Screw Note When this unit is installed in a vehicle without ACC accessory position on the ignition switch red cable must be wired to the terminal that can detect the operation of the ignition key Otherwise battery drain may result Use this unit in other than the following condi tions could result in fire or malfunction Vehicles with a 12 volt battery and negative...

Page 2: ...use 10 A 50 cm 20 in 20 cm 7 7 8 in This product Connecting the Units ENGLISH 7 When not connecting a rear speaker lead to a Subwoofer Yellow Connect to the constant 12 V supply terminal Red Connect to terminal controlled by ignition switch 12 V DC Orange white Connect to lighting switch terminal Yellow black If you use an equipment with Mute function wire this lead to the Audio Mute lead on that ...

Page 3: ...eau avant il peut être fixé avec la vis fournie Garniture Vis Tableau de bord ou console Support de montage fourni avec la voiture Vis Connexions des appareils FRANÇAIS Remarque Si cet appareil est installé dans un véhicule sans position ACC accessoire sur le commutateur d allumage le câble rouge doit être connecté à une borne qui peut détecter la position du commu tateur d allumage Sinon la batte...

Page 4: ...te qui ne sont pas connectés aux enceintes Connexions des appareils FRANÇAIS 7 Quand aucun câble d enceinte arrière n est connecté au caisson de grave 16 cm iPod avec connecteur Dock Port de connexion Dock Connecteur Dock Câble d interface 1 5 m Câble USB Connectez le lecteur audio portable USB ou la mémoire USB vendu séparément Résistance fusible Résistance fusible 50 cm Prise d antenne Sortie du...

Reviews: