background image

1

3980-A2-GZ41-20

June 1998

COMSPHERE 3811

Plus Modem

Installation Instructions
Document Number 3980-A2-GZ41-20

June 1998

User’s Guide

This document provides basic installation instructions

for the COMSPHERE 3811Plus (Model 3981) modem.
For complete configuration and operation instructions,
refer to the COMSPHERE 3800Plus Modems User’s
Guide
 (Document Number 3980-A2-GB30).

Contact your local sales representative, service

representative, or distributor directly for any help needed.
For additional information concerning warranty, sales,
service, repair, installation, documentation, training,
distributor locations, or Paradyne worldwide office
locations, use one of the following methods:

Via the Internet:  Visit the Paradyne World Wide
Web site at http://www.paradyne.com

Via Telephone:  Call our automated call system to
receive current information via fax or to speak with a
company representative.

Within the U.S.A., call 1-800-870-2221

Outside the U.S.A., call 1-727-530-2340

Important Safety Instructions

1. Read and follow all warning notices and

instructions marked on the product or included in
the manual.

2. Slots and openings in the cabinet are provided for

ventilation. To ensure reliable operation of the
product and to protect it from overheating, these
slots and openings must not be blocked or
covered.

3. General purpose cables may be provided with this

product. Special cables, which may be required by
the regulatory inspection authority for the
installation site, are the responsibility of the
customer.

4. When installed in the final configuration, the

product must comply with the applicable Safety
Standards and regulatory requirements of the
country in which it is installed. If necessary,
consult with the appropriate regulatory agencies
and inspection authorities to ensure compliance.

In addition, if the equipment is to be used with

telecommunications circuits, take the following
precautions:

Never install telephone wiring during a lightning
storm.

Never install telephone jacks in wet locations
unless the jack is specifically designed for wet
locations.

Never touch uninsulated telephone wires or
terminals unless the telephone line has been
disconnected at the network interface.

Use caution when installing or modifying telephone
lines.

Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote
risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the
vicinity of the leak.

Government Requirements

Notice to Users of the United States Public
Switched Telephone Network

1. This equipment complies with Part 68 of the FCC

rules. On the equipment is a label that contains,
among other information, the FCC registration
number and ringer equivalence number (REN) for
this equipment. The label is located on the circuit
card assembly of the 3811Plus. If requested, this

TM

Summary of Contents for COMSPHERE 3800PLUS













Reviews: