Panduit PDM4.0 EI Setup Download

Page: 1 / 10

PDM4.0 EI Setup

PA28091A01

Rev. 02 2-2017

PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM

ELECTRONIC INTERFACE USER MANUAL

Original Instructions

EI (Electronic Interface) Instructions

For use with the following Systems &

respective Operational Manuals:

PAT 4.0 FAMILY TOOLS: Automatic Cable Tie Installation Tools

PDM4.0: Dispenser

PHM: Feeder Hoses

Operation Manual (PA27647A01)

PDM4.0 Data Manager Operations Manual (PA25060A01)

EI I/O port (25 Pin Connector) is internally connected

to Optically Isolated Modules,

WARNING

•

TO REDUCE THE RISK OF INJURY,

USER MUST READ INSTRUCTION
MANUAL

Email:

[email protected]

EU Website:

www.panduit.com/emea

EU Email: emeatoolservicecenter

@panduit.com

www.panduit.com

Panduit Corp. • Tinley Park, IL USA

Technical Support

Tel: 1-800-777-3300

Panduit Europe • EMEA Service Center

Almelo, Netherlands

Tel: +31 546 580 452 • Fax: +31 546 580 441

Summary of Contents for PDM4.0 EI











Search results

Summary of Contents for PDM4.0 EI

Reviews:

Related manuals for PDM4.0 EI

Brands by name

Popular brands

Panduit PDM4.0 EI, Setup

Search results

Summary of Contents for PDM4.0 EI

Reviews:

Related manuals for PDM4.0 EI

Brands by name

Popular brands