background image

Page 1

Page 1

PAC

®

 | 866-931-8021 | [email protected] 

©2016 Pacific Accessory Corporation

www.pac-audio.com

Rev. 113016

Pacific Accessory Corporation

PAC is an AAMP power brand

RPK5-GM4101

 

 Complete Radio Replacement Kit with 

Integrated Climate Control Retention for 

2010-2015 Chevrolet Camaro

Removing the factory radio from the vehicle

1.1 -

 Apply the parking brake. Move the transmission shift 

assembly to the most rearward position possible. Use a 

flat bladed plastic trim tool and release the retainer tabs 

securing the front floor console front cover to the console 

assembly. Lift the cover (1) up and rearward making sure that 

the accessory power receptacle and the electronic traction 

control switch clears the transmission shift assembly. It may be 

necessary to pop them loose from the underside to achieve 

clearance. Disconnect the electrical connections.

1.2 -

 Remove the 2 x 7mm bolts (1) securing the radio 

control assembly (2) into the dash. Then use a flat-

bladed plastic trim tool in order to release the retainer 

clips securing the radio control assembly (2) to the 

instrument panel. Disconnect the electrical connections.

Parts List

The RPK5-GM4101 includes everything you need for a professional installation of an aftermarket radio in your Camaro. 
This kit contains:

1. Dash Kit 

•  (x1) PAC HVAC Control Panel (Transfer of the factory HVAC knobs is required. See instructions below) 

•  (x2) Radio Mounting Brackets (One left and one right) 

•  (x1) Pocket (For single din applications) 

•  (x8) Radio Mounting Screws

2. RP5-GM4101 (Camaro specific radio replacement module)

3. Camaro specific antenna adapter (BAA-DIN22).

4. Rear camera retention cable for vehicles equipped with the MyLink system.

5. USB retention cable. This cable is compatible with vehicles equipped with the MyLink radios and vehicles equipped with the  

    standard non-touchscreen radios. It will require that the cable be ran to the back of the center console.

6. AUX retention cable for 2010-2012 vehicles equipped with the standard non-touchscreen radios also equipped with a USB port.

 

Overview

The RPK5-GM4101 is a complete radio replacement kit with integrated climate control retention for the 2010-2015 Chevrolet 

Camaro. This kit utilizes the factory HVAC control knobs for a more factory look and experience. To add to the factory look 

and experience the exterior temperature display is retained by a small OLED display at the top of the kit retaining this valuable 

vehicle feature. This kit also includes all of the modules and cables needed to retain all of the important features of the factory 

system such as OnStar, factory warning chimes, factory Bluetooth, steering wheel mounted radio controls, factory reverse 

camera, factory amplifier (if equipped), AM/FM reception, factory AUX jack (if equipped) and the factory USB port (if equipped).

Table of Contents:                                                                        Page:

1. Factory Radio Removal ------------------------------------------------------ 1-2

2. Disassembly of the factory HVAC control module --------------------- 2-3

3. Assembly of the PAC HVAC control module ---------------------------- 3-4

4. RP5-GM4101 Instructions --------------------------------------------------- 4-6

5. AUX & USB Cable Installation ------------------------------------------------ 7

6. Temperature Display Settings ------------------------------------------------- 7

7. Sub-Dash Preparation ----------------------------------------------------------- 7

8. Kit Assembly Instructions ------------------------------------------------------- 8

9. Installation of the PAC HVAC control module --------------------------- 8-9

Summary of Contents for RPK5-GM4101










Reviews: