Thank you for purchasing this product of
Olympia Electronics. A European manufacturer.
GENERAL
o
These luminaires are used indoors
(
ta 40 C
)
where emergency light is needed. Each
luminaire must be permanently connected to
mains power supply
.
In normal operation the
power
and the
charge
indicators light to show
that the batteries are in charging condition. In
case of a mains power supply failure the
power
and the
charge
indicators turns off and
the luminaire will light the spot lamps
automatically in emergency mode. When the
mains power supply is restored the device
turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions
ο
n page 2.
OPERATION
When the device is powered from the mains
,
the
charge
and
power
indicat
ors
should
light
.
Th
e
charge
indicator confirms
the
charg
ing of
the batter
ies
. If
it does
not li
gh
t, probably, the
batter
ies are
disconnected. If
it does
not li
gh
t
and the batter
ies
are
connected, then contact
the technician.
As long as the charge indicator
blinks, the batteries of the luminaire are
charging and in this period, any autonomy test
must be avoided. When the charging circle is
complete, the indicator lights continuously (it
can be used as an indication of a power
interruption). The batteries charging is done by
an 3 stages technological advanced procedure,
to ensure the appropriate and full charging of
the batteries.
The
power
indicator confirms
the
proper
connection to the
mains
. The
TEST
butto
n, has
a dual use. If pressed
instantlly
while the device
is
connected to the mains
, the device simulates
the
power interruption
,
by
lighting
the
lamps for
3
''. In this way
,
we can control the driver circuit
of
the lamps
and
the
lamps as indicated in
paragraph
3
in
the text
below .
When the voltage is interrupted, with
corresponding press
ing
s of the button,
we ca
n
choose
the operation of 2,1
or
no
lamp
s
, either to
increase the autonomy time or not to consume
the
battery power unnecessarily. This option is
canceled when the network is restored.
ΑΤΤΕΝΤΙΟΝ
!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only
.
2.
The device must be connected to the mains
power supply thru a fuse dependent by the total
amount of the line’s power load
.
3.
It is sugested to check every month the
indication LED for battery charging, and by
pushing instantly the TEST button to check the
emergency cirquit and the lamps. If the
luminaire does not light
contact the installer.
4.
It is sugested to check every 6 months the
Page
1
from
2
``POWER LIGHT`` SERIES FOR NON-MAINTAINED EMERGENCY LUMINAIRES
Bayblend FR3010
,
transparent
polycarbonate
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Pb)
CHARGING TIME
INDICATIONS
-
CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
24h
Power indicator, battery charge indicator, TEST button
From overcharge and deep discharge
IP 42
o
0 to 40 C
Up to 95%
3 years
(1
year for the lamps and the battery
)
90 min
6
0 min
3
h
5
80lm
1620lm
5
8
0
lm
2
x20W (halogen
)
2
x20W (halogen
)
2
x
55
W (halogen
)
3330
gr.
5300
gr.
EN 60598-1, EN 60598-2-22
, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
302 x 94 x 330 mm
302 x 94 x 330 mm
GR-2
1
GR-29
GR-21/Η
220-240V AC/50-60Hz
12V/7Ah
14VA
24VA
2
x12V/7Ah
923029000_
23
_02
3
High Quality European based Manufacturers
3
25
x
120
x 3
80
mm
729
0gr.
