background image

Shock Absorber for Honda PCX 150-2018

HO 810

Mounting Instructions

Note!

Please note that this image is a general representation 

of the product and may differ slightly from your product.

Note!

Please note that during storage and transportation, 

especially at high ambient temperature, some of the oil 

and grease used for assembling may leak and stain the 

packaging. This is in no way detrimental to the product, 

wipe off the excessive oil/grease with a cloth.

Warning!

Before installing this product, read the Öhlins Owner’s 

Manual. The shock absorber is an important part of your 

vehicle and will affect the stability.

Note!

Before installing this product, check the contents of 

the kit. If anything is missing, please check an Öhlins 

dealer.

Kit Contents
Description

Part No

Pcs

Shock absorber

HO 810

2

Bracket, mudguard

61125-01

1

Screw M6x8  

05404-11

1

Screw M8x35

00432-01

2

Screw M6x45 

01046-62

2

Screw M6x14 

00382-16

1

Sleeve 7/13.9-10

61123-14

2

Washer  6.4/18/1.6 

00426-04

1

Tool preload adjuster

03199-03

1

Sticker set   "ÖHLINS" 

10207-01

1

Owners manual road & track

07241-02

1

Alternative spring

Spring 46
/200/prog 15-24N/mm

60360-03

2

Summary of Contents for HO 810













Reviews: