![background image](http://html1.mh-extra.com/html/observint/blk-cpd227vh/blk-cpd227vh_quick-installation-manual_3178540001.webp)
1
BLK-CPD227VH_CQ
9/26/12
Base
Camera
module
L-wrench
Dome
Base
cable
access
Mounting
screws (2)
Camera
module
screws (2)
Dome
screws (3)
Side cable
access, cap
Dome
retention
cable
Drop
cable
4.
Select the best fasteners to secure the base to the mounting surface. Screws provided with the
camera are adequate many surface types.
5.
Drill holes in the mounting surface as required for the mounting screws (wall inserts, etc.), and the
cables, if needed.
6.
Route the video / power extension cables from your monitoring equipment into the camera base.
Note that the extension cable connectors are usually different at each end.
7.
Connect the video / power extension cables to the drop cable inside the base cavity.
8.
Reattach the camera module to the based using the two screws removed earlier.
9.
Connect the video / power extension cable to your camera, then connect the other end to a video
monitor and 12 Vdc or 24 Vac power source.
NOTE
: 1) The camera power cable provides a 2-pin
connector; an adapter with screw-down terminals is included in the box. 2) If powering the camera
with 12 Vdc, observe the polarity marked on the power drop cable.
12 Vdc polarity guide
Video drop cable
Terminal adapter
Power drop cable
Drop cable connectors
10. Verify that you can see video from your camera at the monitoring equipment.
BLK-CPD227VH 650 Line Outdoor
Vandalproof IR Camera
Quick Installation Guide
This document guides you through the basic steps to install and use your BLK-CPD227VH camera. The
camera includes 2.8-12 mm lens, 12 Vdc or 24 Vac powering.
Camera features include:
•
Can be installed indoors or outdoor.
•
650 TV-line resolution in color, 720 TVL B / W
•
Advanced Gen V DSP
•
IP67 rated (waterproof)
•
Durable enclosure: body is aluminum, dome is polycarbonate
•
Smart DNR technology efficiently reduces noise in low light conditions
•
75 foot range with Smart IR 24-LED IR LED array
•
3-axis camera gimbal - mountable on ceiling, wall or sloped surface
•
Day & Night function (ICR)
•
Support up to 8 privacy zones
•
Digital Wide Dynamic Range (DWDR)
•
Multi function : High-Light Mask, Lens Shading Compensation, Smart Motion Detection
•
Smart IR technology greatly improves camera image in B / W mode when the IR LED array is on
•
Multi-language full OSD support
Precautions
•
Do not install the camera in locations subject to moisture or vibration.
•
Do not scratch the camera, especially lens or dome cover.
•
Operate the camera within the specified temperature range 14
°
F ~ 122
°
F (-10
°
C ~ 50
°
C).
•
Handle with care. Dropping it can cause serious damage to the camera.
•
Do not install the camera in locations where direct sunlight shines onto or be reflected onto the lens.
•
Use a 12 Vdc, 1A regulated power adapter, or 24 Vac power adaptor.
Installation
1.
Remove the camera dome by loosening the three dome cover screws with the L-wrench provided,
then lifting off the cover. See the graphic to the right.
2.
Remove the camera module assembly from the base by removing the two camera module screws.
3.
Using the base as a template, mark the locations on the mounting surface for the mounting screws
(2) and the hole for the network video and power cables routed into the base. Note that the network
cable can be routed or through the mounting surface at the center of the base, or in through a cap
on the side of the base. The camera can be mounted on a ceiling or wall.