background image

Copyright

©

 2019 Nortek Security & Control, LLC

10022113 A

MM272

This product meets the requirements of UL325, the standard for gate operator safety.

Installation Manual

Example of finished installation

(installations vary slightly on different types of gates)

 

120 Volt indoor

Transformer

(surge protector 

not supplied)

Horizontal Support

Gate Swings Evenly and Freely

Hung Firmly and Plumb

Post Bracket

Control Box

Fence Post Set in Concrete

Run 1000' (max.) of low

voltage wire to control

box from transformer

(wire not included).           

Power Cable

Gate Bracket

Warning Sign

First Gate Opener

Post Bracket

Second Gate Opener

Gate Bracket

Horizontal Support

PVC conduit (not included)

to run second opener power

cable under driveway.

12 Volt automotive or marine 

type battery in weather proof 

housing (REQUIRED, not included).  

Mighty Mule® is the retail brand of Nortek Security & Control, LLC

NSC Sales: 800-543-4283 • Fax 850-575-8912

NSC Technical Service 800-543-1236

For Online Technical Support 24 hour/day, 7 day/week visit 

www.mightymule.com

For more information on Mighty Mule’s full line of Automatic Gate Operators and 

Access Controls visit 

www.mightymule.com

Summary of Contents for MIGHTY MULE MM272









































Reviews: