background image

SAQ8976-4

Rev. 12/05

Model N-069M

N-063S

WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.

- Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service

agency or the gas supplier.

Owner’s Guide  and
                      Installation Manual

*SAQ8976   T*

NORITZ America Corporation

Thank you for purchasing this Noritz Gas Water Heater. Before using, please:
Read this manual completely for correct installation and operation instructions.
Completely fill out the warranty registration card (included separately) and
mail the detachable portion to Noritz America Corporation.
Keep this manual (and the remainder of the warranty registration card) where it
can be found whenever necessary.

Low NOx

Approved by

SCAQMD

CERTIFIED

R

 E̲n069M/n063S(01̲13)̲J.p65

05.12.6, 10:34 AM

Page 1

Adobe PageMaker 6.5J/PPC

Summary of Contents for N-063S



































































Reviews: